How should two people safely remove and install a car hood on Mazda 3?

The hood is so cumbersome to take out and onboard, thus this process should be done by two persons at least. Start by opening the hood and then laying blankets or pads over the fenders and cow area to prevent the damage of the body and paint during the lifting. Mark around the hood hinge, so as to make sure that everything comes together when it is being installed. Use your shoulder to hold one corner of the hood and have an assist help you with the other side of the hood. Repeat the procedure of removing the hinge-to-hood bolts in turns and removing the hood. To install it, match the hinge bolts with the marks created above. In order to adjust the hood, loosen the hinge-to-body bolts and adjust the hinges by making minor adjustments and tightening the bolts and then confirming the position. The hood is as well adjustable vertically by clockwise and counterclockwise rotation of each cushion to bring it down or up respectively. Also, it is necessary to periodically coat the hood latch system and the hinges with white, lithium-base grease to avoid binding and wear.

Genuine Mazda 3 Hood

Engine Hood

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Hoods found

View related parts
Mazda 3 Hood Part Number: BPYK-52-31XB
$403.57 MSRP: $542.55
You Save: $138.98 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bonnet
- Replaces: BPYK-52-31X, BP4K-52-310, BPYK-52-31XA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2004-2009 Mazda 3 | S, SP23 | 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Hood Part Number: BBY5-52-31XA
$466.57 MSRP: $627.24
You Save: $160.67 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bonnet
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2010-2013 Mazda 3 | Mazdaspeed | 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Hood Part Number: BBY4-52-31XC
$467.33 MSRP: $628.26
You Save: $160.93 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bonnet
- Replaces: BBY4-52-31XA, BBY4-52-31XB, BBY4-52-31X
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2010-2013 Mazda 3 | i, S | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Hood Part Number: BNYV-52-31XB
$610.41 MSRP: $820.61
You Save: $210.20 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bonnet
- Replaces: BNYV-52-31X, BNYV-52-31XA, BN8V-52-310A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2004-2009 Mazda 3 | i, S, SP23 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Hood Part Number: BRYG-52-31XC
Product Specifications
- Replaces: BRYG-52-31XA, BRYG-52-31XB
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2007-2009 Mazda 3 | Mazdaspeed | 4 Cyl 2.3 L GAS

Mazda 3 Hood

The Mazda 3 Hood is the first line of protection of the car against the weather and flying objects, and it provides access to the engine quite quickly. This hinged Mazda front compartment cover is made of impact-absorbing steel, aluminum, or fiberglass and secures and protects the belts, hoses, and electronic parts inside the compartment against rain, snow, and strong sunlight, but it is easy to unlatch so that the owners can access the compartment or replace the parts. The Hood panel may become bent over time due to dents, scratches, or an irresponsible bang that may loosen the hinges of the panel or cause the latch to become weak, making the engine vulnerable to corrosion. Early designs applied heavier steel material to ensure optimum durability, but later designs tended to switch to skins made of lighter aluminum or composite materials to reduce the weight and improve fuel efficiency without compromising the strength in the event of a crash. Whatever the material it is made of, all Hoods have built-in crumple zones, which collapse in case of a front-end collision to absorb the impact before it hits the cabin. In the event of a collision or rusting that damage the smooth surface, the replacement can be done within a short period of time, thus regaining the protection and that sporty appearance that the buyers of Mazda expect. Handling the latch tenderly, ensuring the hinge bolts, and rubbing paint on the nicks may extend the life cycle and preserve the resale value. During shopping, make sure that it fits the Mazda 3 exactly to be sure that the new Hood fits the fenders and headlights perfectly.

Looking for Hood with proven quality? Choose OEM Hood. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda 3 parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine 3 part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda 3 Hood Parts and Q&A

Hood
BBY5-52-31XA
Q: How should two people safely remove and install a car hood on Mazda 3?
A:
The hood is so cumbersome to take out and onboard, thus this process should be done by two persons at least. Start by opening the hood and then laying blankets or pads over the fenders and cow area to prevent the damage of the body and paint during the lifting. Mark around the hood hinge, so as to make sure that everything comes together when it is being installed. Use your shoulder to hold one corner of the hood and have an assist help you with the other side of the hood. Repeat the procedure of removing the hinge-to-hood bolts in turns and removing the hood. To install it, match the hinge bolts with the marks created above. In order to adjust the hood, loosen the hinge-to-body bolts and adjust the hinges by making minor adjustments and tightening the bolts and then confirming the position. The hood is as well adjustable vertically by clockwise and counterclockwise rotation of each cushion to bring it down or up respectively. Also, it is necessary to periodically coat the Hood Latch system and the hinges with white, lithium-base grease to avoid binding and wear.