How to remove and install the Exterior Door Handle,Door Latch Assembly and Door Lock Cylinder on Mazda 323?

Remove the door trim panel and the plastic watershield. Reach inside the door and disconnect the control links from the latch. Mark the location of the door latch prior to removal and take out the latch retaining screws from the end of the door, noting that on 1997 and later models there is only one latch screw. Detach the door latch, and if equipped with power door locks, remove the door lock solenoid. For installation, align the door latch and securely tighten the door latch screws. Through the door inside access hole, remove the outside handle retention bolts or nuts, and on 1995 and later models, take out the lock cylinder electrical switch retainer and the switch. Remove the control rod from the lock cylinder, then use pliers or a screwdriver to pry the retaining clip upwards and off of the lock cylinder. Pull the outside handle and lock cylinder from the door. For installation, follow the reverse process. The door key cylinder electrical switch may be tested if necessary without removal; disconnect the electrical connector and check that the electrical continuity between the terminals is 0 ohms (no resistance) when in the unlocked position, and 1 K-ohm when in the locked position.

Genuine Mazda 323 Door Latch Assembly

Door Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Door Latch Assemblys found

View related parts
Mazda 323 Lock Part Number: BR71-60-070B
$57.30 MSRP: $76.41
You Save: $19.11 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Speedometer Cable; Lock Actuator, Speedometer Cable Assembly
- Replaced by: BTAR-60-070
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990 Mazda 323 | Base, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: B001-62-310A
$57.35 MSRP: $76.48
You Save: $19.13 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock, Lift Gate
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1986-1989 Mazda 323 | Base, DX, GT, GTX, LX, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: BR9458310D
Product Specifications
- Other Name: Lock Right, Door
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1994 Mazda 323 | Base, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: BR93-59-310C
Product Specifications
- Other Name: Lock Left, Door
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1994 Mazda 323 | Base, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: BF67-62-310C
Product Specifications
- Other Name: Lock, Lift Gate
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1986-1989 Mazda 323 | Base, DX, GT, GTX, LX, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: B468-62-310A
Product Specifications
- Other Name: Lock, Lift Gate
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1994 Mazda 323 | Base, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: B218-62-380D
Product Specifications
- Other Name: Remote Control
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1987 Mazda 323 | Base, DX | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: B218-62-310D
Product Specifications
- Other Name: Lock, Lift Gate
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1986-1988 Mazda 323 | Base, DX, GT, GTX, LX, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: B216-62-380D
Product Specifications
- Other Name: Remote Control; Release Wire
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1986-1987 Mazda 323 | Base, DX | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: B111-58-310B
Product Specifications
- Other Name: Lock Right, Door
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1986-1989 Mazda 323 | Base, DX, GT, GTX, LX, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: B092-59-310B
Product Specifications
- Other Name: Lock Left, Door
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1986-1989 Mazda 323 | Base, DX, GT, GTX, LX, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda 323 Lock Part Number: B092-58-310B
Product Specifications
- Other Name: Lock Right, Door
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1986-1989 Mazda 323 | Base, DX, GT, GTX, LX, SE | 4 Cyl 1.6 L GAS

Mazda 323 Door Latch Assembly

Looking for Door Latch Assembly with proven quality? Choose OEM Door Latch Assembly. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda 323 parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine 323 part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda 323 Door Latch Assembly Parts and Q&A

Lock
B468-62-310A
Q:
How to remove and install the Exterior Door Handle,Door Latch Assembly and Door Lock Cylinder on Mazda 323?
A:
Remove the door trim panel and the plastic watershield. Reach inside the door and disconnect the control links from the latch. Mark the location of the door latch prior to removal and take out the latch retaining screws from the end of the door, noting that on 1997 and later models there is only one latch screw. Detach the door latch, and if equipped with power door locks, remove the door lock solenoid. For installation, align the door latch and securely tighten the door latch screws. Through the door inside access hole, remove the outside handle retention bolts or nuts, and on 1995 and later models, take out the lock cylinder electrical switch retainer and the switch. Remove the control rod from the lock cylinder, then use pliers or a screwdriver to pry the retaining clip upwards and off of the lock cylinder. Pull the outside handle and lock cylinder from the door. For installation, follow the reverse process. The door key cylinder electrical switch may be tested if necessary without removal; disconnect the electrical connector and check that the electrical continuity between the terminals is 0 ohms (no resistance) when in the unlocked position, and 1 K-ohm when in the locked position.