How should the hood be removed and installed safely and effectively on Mazda 6?

The hood is clumsy to take out and install thus at least two individuals should carry out this action. Start by opening up the hood and covering the body and paint with blankets or pads over the hood fenders and cowl to prevent damage in the lift. Mark around the hood hinge in order to make sure that it is aligned correctly during the installation process. Having another person to assist you on one side of the hood, hold on to the bottom corner and with your shoulder, hold it steady as you make turns to unscrew the hinge-to-hood bolts so as to remove the hood. To install, position the hinge bolts to fit in the marks that have been made. In order to fine-tune the hood, loosen the hinge-to-body bolts and adjust the hood in the fore-and-aft and side-to-side directions, then proceed to tighten the bolts with each minute step. The hood also is adjustable vertically to be in line with the fenders by clockwise rotation of each cushion to lower the hood down and anti clockwise rotation to raise the hood up. The hood latch assembly and the hinges should as well be regularly oiled with white, lithium-base grease to avoid binding and wear.

Genuine Mazda 6 Hood

Engine Hood

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Hoods found

View related parts
Mazda 6 Hood Part Number: GBY0-52-31XB
$490.63 MSRP: $659.58
You Save: $168.95 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bonnet; Hood
- Replaces: GBY0-52-31X, GBY0-52-31XA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2018-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Hood Part Number: GHY0-52-31X
$509.81 MSRP: $685.37
You Save: $175.56 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bonnet
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2017 Mazda 6 | Grand Touring, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Hood Part Number: GK2A-52-310D
$502.70 MSRP: $675.80
You Save: $173.10 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bonnet
- Replaces: GK2A-52-310B, GK2A-52-310C
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2008 Mazda 6 | i, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Hood Part Number: GS3L-52-310-SP
$507.40 MSRP: $682.12
You Save: $174.72 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bonnet
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Mazda 6 | i, S | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Hood Part Number: GPYA-52-31XC
Product Specifications
- Other Name: Bonnet
- Replaces: GPYA-52-31XB, GPYA-52-31X, GPYA-52-31XA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2007 Mazda 6 | Mazdaspeed | 4 Cyl 2.3 L GAS

Mazda 6 Hood

The Mazda 6 Hood protects the engine bay against rain, debris, and even impacts and can be easily lifted to see inside. This hinged Hood panel, besides protecting essential components, serves as a point of visual interest, allowing the car to look smooth and familiar. Its form also contributes to directing airflow over the windshield and thereby decreasing drag. In early days, Mazda sedans were made from strong stamped steel, but more recent models use lighter aluminum and even fiberglass skins, each according to their respective strengths, ability to resist corrosion, and low weight. No matter the material, all Hoods come with hidden hinges and lock at the front with a latch so that drivers can pop it from the cabin then use a simple rod to prop it upward to reach filters, belts, and fluids. Inbuilt crumple areas allow the sheet to crumple during a frontal impact, absorbing energy before it is transmitted to the passenger cell, which is also a major safety measure common to the two main style periods. Such a reliable Hood design helps Mazda owners lift the panel without any assistance. In case a collision or rogue cart leaves the surface dented or cracked, a replacement panel will restore the looks and the air circulation that will help dissipate heat in the compartment. To most Mazda enthusiasts, the Hood is a functional shield and a sculpted expression that has brought the spirit of the 6 lineage together.

Looking for Hood with proven quality? Choose OEM Hood. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda 6 parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine 6 part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda 6 Hood Parts and Q&A

Hood
GK2A-52-310D
Q: How should the hood be removed and installed safely and effectively on Mazda 6?
A:
The hood is clumsy to take out and install thus at least two individuals should carry out this action. Start by opening up the hood and covering the body and paint with blankets or pads over the hood fenders and cowl to prevent damage in the lift. Mark around the hood hinge in order to make sure that it is aligned correctly during the installation process. Having another person to assist you on one side of the hood, hold on to the bottom corner and with your shoulder, hold it steady as you make turns to unscrew the hinge-to-hood bolts so as to remove the hood. To install, position the hinge bolts to fit in the marks that have been made. In order to fine-tune the hood, loosen the hinge-to-body bolts and adjust the hood in the fore-and-aft and side-to-side directions, then proceed to tighten the bolts with each minute step. The hood also is adjustable vertically to be in line with the fenders by clockwise rotation of each cushion to lower the hood down and anti clockwise rotation to raise the hood up. The Hood Latch assembly and the hinges should as well be regularly oiled with white, lithium-base grease to avoid binding and wear.