How to properly replace a Brake Rotor on Mazda Protege?

Relax the wheel lug nuts, elevate the car and hold it firmly on jackstands. Take off the wheel and place in the lug nuts to secure the Brake Rotor to be firmly seated perhaps with some washers to make it fit. Take off the brake caliper and leave the brake hose attached and hang it out of the way using a piece of wire; make sure it is not suspended on the brake hose only. Look at the rotor face with naked eyes to identify marks of scores and damage; a shallow groove with light scratches and 0.039-inch deep are normal; however, deep scoring, more than 0.039-inch, needs to be refinished. Test the rotor on both sides of the rotor because of the extreme wear. In checking rotor run out you should insert a dial indicator of about 1/2-inch of the outer edge, position it to zero and turn the rotor in slow movements, not letting the reading reach the allowable limit; the rotor should be resurfaced anyway to remove the brake pedal pulsation. Make sure that the rotor is not machined less than the recommended minimum thickness which is inspectable using a micrometer. Divest the lug nuts that are holding the rotor and remove the rotor off the hub. With the models with ABS, disconnect the speed sensor connector, remove clips that hold the hydraulic brake line, and remove a sensor. Install the caliper and crimp the caliper bolts to the required torque by placing the new rotor on top of the wheel studs and placing the caliper. Install the ABS wheel sensor removed (with due clearance to the toothed rotor). Install the wheel, lower the vehicle, and screw in the lug nuts to the required torque. Test the supply of brake fluid and fill it up where needed and press the brake pedal a couple of times before driving to confirm the right functioning of the brake pads and rotor.

Genuine Mazda Protege Brake Rotor

Disc Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Brake Rotors found

View related parts
Mazda Protege Rotor Part Number: BJ1Y-33-25X
$77.20 MSRP: $102.95
You Save: $25.75 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate, Disc
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1999-2003 Mazda Protege | DX, ES, LX, MP3, Mazdaspeed | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Mazda Protege Rotor Part Number: BJ0Y-33-25X
$77.20 MSRP: $102.95
You Save: $25.75 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate, Disc
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1999-2001 Mazda Protege | DX, LX | 4 Cyl 1.6 L GAS
View related parts
Mazda Protege Rotor Part Number: GTYF-26-251C
$81.70 MSRP: $108.95
You Save: $27.25 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor, Brake
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2003 Mazda Protege | DX, ES, LX, MP3, Mazdaspeed | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS
View related parts
Mazda Protege Rotor Part Number: G25Y-33-25XA
$89.10 MSRP: $118.82
You Save: $29.72 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor, Front
- Replaces: GF3Y-33-25XA, GF3Y-33-25X
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2003 Mazda Protege | DX, ES, LX, MP3, Mazdaspeed | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS
View related parts
Mazda Protege Rotor Part Number: G25Y-26-251A
$91.14 MSRP: $121.54
You Save: $30.40 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate, Disc(W/Coating)
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2003 Mazda Protege | DX, ES, LX, MP3, Mazdaspeed | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS
View related parts
Mazda Protege Rotor Part Number: GA4Y-33-25XJ
$94.93 MSRP: $126.59
You Save: $31.66 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor, Brake
- Replaces: GA4Y-33-25XH
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2003 Mazda Protege | DX, ES, LX, MP3, Mazdaspeed | 4 Cyl 2.0 L GAS
View related parts
Mazda Protege Rotor Part Number: BB4C-26-251C
$95.20 MSRP: $126.96
You Save: $31.76 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Disc Plate; Brake Rotor
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1998 Mazda Protege | 4WD, DX, ES, LX, SE | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Rotor Part Number: BB7E-33-25XD
$77.20 MSRP: $102.95
You Save: $25.75 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate, Disc; Brake Rotor
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1991-1998 Mazda Protege | 4WD, Base, DX, ES, LX | 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Rotor Part Number: B26Y-33-25XA
$90.56 MSRP: $120.77
You Save: $30.21 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate, Disc
- Replaces: BR70-33-25XF
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1998 Mazda Protege | DX, LX, SE | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Rotor Part Number: B530-33-25XE
Product Specifications
- Other Name: Plate, Disc
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1991 Mazda Protege | 4WD, DX, LX, SE | 4 Cyl 1.8 L GAS

Mazda Protege Brake Rotor

Looking for Brake Rotor with proven quality? Choose OEM Brake Rotor. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda Protege parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine Protege part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda Protege Brake Rotor Parts and Q&A

Rotor
GA4Y-33-25XJ
Q:
How to properly replace a Brake Rotor on Mazda Protege?
A:
Relax the wheel lug nuts, elevate the car and hold it firmly on jackstands. Take off the wheel and place in the lug nuts to secure the Brake Rotor to be firmly seated perhaps with some washers to make it fit. Take off the Brake Caliper and leave the brake hose attached and hang it out of the way using a piece of wire; make sure it is not suspended on the brake hose only. Look at the rotor face with naked eyes to identify marks of scores and damage; a shallow groove with light scratches and 0.039-inch deep are normal; however, deep scoring, more than 0.039-inch, needs to be refinished. Test the rotor on both sides of the rotor because of the extreme wear. In checking rotor run out you should insert a dial indicator of about 1/2-inch of the outer edge, position it to zero and turn the rotor in slow movements, not letting the reading reach the allowable limit; the rotor should be resurfaced anyway to remove the brake pedal pulsation. Make sure that the rotor is not machined less than the recommended minimum thickness which is inspectable using a micrometer. Divest the lug nuts that are holding the rotor and remove the rotor off the hub. With the models with ABS, disconnect the speed sensor connector, remove clips that hold the hydraulic Brake Line, and remove a sensor. Install the caliper and crimp the caliper bolts to the required torque by placing the new rotor on top of the wheel studs and placing the caliper. Install the ABS wheel sensor removed (with due clearance to the toothed rotor). Install the wheel, lower the vehicle, and screw in the lug nuts to the required torque. Test the supply of brake fluid and fill it up where needed and press the brake pedal a couple of times before driving to confirm the right functioning of the Brake Pads and rotor.