How to disconnect the ignition lock cylinder and ignition switch on Mazda Protege?

Disconnect the negative battery cable and on 1995 and later models, disable the airbag of the driver. Take off the steering column upper and lower covers, and then the lower dash panel. Follow wire that connects ignition switch to electrical connector and disconnect it, and test continuity in each of the mentioned positions. Unscrew the electrical connector of the switch, unscrew the screw, and then part the switch and assembly of steering lock. The opposite of removal is installation.

How to remove and install the door lock and ignition lock cylinder on Mazda Protege?

Remove the door trim panel and the plastic watershield. Reach inside the door and disconnect the control links from the latch. Mark the location of the door latch prior to removal and take out the latch retaining screws from the end of the door, noting that on 1997 and later models there is only one latch screw. Detach the door latch, and if equipped with power door locks, remove the door lock solenoid. For installation, align the door latch and securely tighten the door latch screws. Through the door inside access hole, remove the outside handle retention bolts or nuts, and on 1995 and later models, take out the lock cylinder electrical switch retainer and the switch. Remove the control rod from the lock cylinder, then use pliers or a screwdriver to pry the retaining clip upwards and off of the lock cylinder. Pull the outside handle and lock cylinder from the door. For installation, follow the reverse process. The door key cylinder electrical switch may be tested if necessary without removal; disconnect the electrical connector and check that the electrical continuity between the terminals is 0 ohms (no resistance) when in the unlocked position, and 1 K-ohm when in the locked position.

Genuine Mazda Protege Ignition Lock Cylinder

Ignition Key Lock Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Ignition Lock Cylinders found

View related parts
Mazda Protege Lock Cylinder Part Number: BG1N-76-250B
$94.56 MSRP: $126.11
You Save: $31.55 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Glove; Lock Cylinder
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1995-1998 Mazda Protege | DX, ES, LX | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Ignition Lock Cylinder Part Number: GEYM-76-290
$268.95 MSRP: $358.67
You Save: $89.72 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Steering Lock; Steering Lock
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1999-2000 Mazda Protege | DX, ES, LX | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Ignition Lock Cylinder Part Number: BJYE-76-290
$293.81 MSRP: $391.82
You Save: $98.01 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Steering Lock; Steering Lock
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1999-2000 Mazda Protege | DX, ES, LX | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Ignition Lock Cylinder Part Number: BG1R-76-290C
$287.96 MSRP: $384.03
You Save: $96.07 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Set; Steering Lock
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1995-1998 Mazda Protege | DX, ES, LX | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Ignition Lock Cylinder Part Number: BR70-76-290F
$315.56 MSRP: $420.83
You Save: $105.27 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Set; Cylinder & Keys, Lock Housing, Steering Lock
- Replaces: BR70-76-290C
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1994 Mazda Protege | 4WD, Base, DX, LX, SE | 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Ignition Lock Cylinder Part Number: B458-76-290G
$50.94 MSRP: $66.86
You Save: $15.92 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Set; Cylinder & Keys, Steering Lock
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1994 Mazda Protege | 4WD, Base, DX, LX, SE | 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Ignition Lock Cylinder Part Number: BLYD-76-290
Product Specifications
- Other Name: Key Sub Set, Steering Lock; Steering Lock
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2003 Mazda Protege | DX, ES, LX, Mazdaspeed, MP3 | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS
View related parts
Mazda Protege Cylinder & Keys Part Number: BR7076250B32
Product Specifications
- Other Name: Key Set
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1994 Mazda Protege | 4WD, Base, DX, LX, SE | 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Lock Cylinder Part Number: FD15-76-250C
Product Specifications
- Other Name: Key Sub Set, Glove
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1996 Mazda Protege | DX, ES, LX | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Protege Ignition Lock Cylinder Part Number: GGYB-76-290
Product Specifications
- Other Name: Key Sub Set, Steering Lock; Steering Lock
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2003 Mazda Protege | DX, ES, LX, Mazdaspeed, MP3 | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS
View related parts
Mazda Protege Ring Part Number: LA01-60-261
Product Specifications
- Other Name: Ring Set; Cylinder Bezel, Lock Cylinder, Ring
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 1990-1994 Mazda Protege | 4WD, Base, DX, LX, SE | 4 Cyl 1.8 L GAS

Mazda Protege Ignition Lock Cylinder

Looking for Ignition Lock Cylinder with proven quality? Choose OEM Ignition Lock Cylinder. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda Protege parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine Protege part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda Protege Ignition Lock Cylinder Parts and Q&A

Ignition Lock Cylinder
BJYE-76-290
Q: How to disconnect the ignition lock cylinder and ignition switch on Mazda Protege?
A:
Disconnect the negative battery cable and on 1995 and later models, disable the airbag of the driver. Take off the steering column upper and lower covers, and then the lower dash panel. Follow wire that connects ignition switch to electrical connector and disconnect it, and test continuity in each of the mentioned positions. Unscrew the electrical connector of the switch, unscrew the screw, and then part the switch and assembly of steering lock. The opposite of removal is installation.
Ring
LA01-60-261
Q: How to remove and install the door lock and ignition lock cylinder on Mazda Protege?
A:
Remove the door trim panel and the plastic watershield. Reach inside the door and disconnect the control links from the latch. Mark the location of the door latch prior to removal and take out the latch retaining screws from the end of the door, noting that on 1997 and later models there is only one latch screw. Detach the door latch, and if equipped with power door locks, remove the door lock solenoid. For installation, align the door latch and securely tighten the door latch screws. Through the door inside access hole, remove the outside handle retention bolts or nuts, and on 1995 and later models, take out the lock cylinder electrical switch retainer and the switch. Remove the control rod from the lock cylinder, then use pliers or a screwdriver to pry the retaining clip upwards and off of the lock cylinder. Pull the outside handle and lock cylinder from the door. For installation, follow the reverse process. The door key cylinder electrical switch may be tested if necessary without removal; disconnect the electrical connector and check that the electrical continuity between the terminals is 0 ohms (no resistance) when in the unlocked position, and 1 K-ohm when in the locked position.