How to replace the ignition lock cylinder and ignition switch on Mazda 6?

Unscrew the cable off the negative side of the battery. Take out knee bolster trim panel, knee bolster, upper and lower steering columns covers, then bend the steering column to the lowest. It should be done with caution since doing both of them at the same time of taking out the ignition switch and key lock cylinder may result in damage of the steering column. Unscrew the electrical connector the ignition switch, then screw out the mounting screw and press the release tabs so that the ignition switch can be pulled off the steering column. Installation of the switch is the opposite of its removal and is best installed in a snapping manner. The ignition switch and key lock cylinder should also be taken with caution. 1. Turn ignition key on 2008 and earlier models or ACC off 2009 and later models. Depress the release button of the key lock cylinder with a proper tool and take out the key lock cylinder. In order to install the key lock cylinder, it is necessary to insert the key lock cylinder into the housing of the lock cylinder and press it inside until it clicks. Ensure that the ignition switch is working properly in the OFF, ACC, RUN and START positions with installation being the opposite of uninstallation. It is not necessary to remove the lock cylinder illumination ring in order to replace the lock cylinder. Unscrew the electrical connector out of the illumination ring, unscrew the lock tabs and take out the illumination ring. Installation is its counterpart, and it is opposite to remove, and the ring should be able to be placed.

How to disconnect and remove the Ignition Lock Cylinder and Trunk Lid Latch on Mazda 6?

Disconnect the cable from the negative battery terminal and remove the trunk lid trim panel. Rotate the trunk lid actuator rod mounting clip and disconnect the rod from the trunk lid key lock cylinder assembly, then disconnect the electrical connector from the lock cylinder if equipped. Remove the mounting nuts and maneuver the lock cylinder out from the trunk lid, with installation being the reverse of removal. Next, disconnect the actuator rod from the trunk lid lock cylinder and the electrical connector from the trunk lid latch. Remove the latch mounting bolts and take out the latch, with installation again being the reverse of removal.

Genuine Mazda 6 Ignition Lock Cylinder

Ignition Key Lock Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Ignition Lock Cylinders found

View related parts
Mazda 6 Cylinder Part Number: GE4T-64-09YB-72
$4.41 MSRP: $5.88
You Save: $1.47 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Glove Lid; Lock Cylinder
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2008 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Ignition Lock Cylinder Part Number: GPYB-76-14XB
$373.31 MSRP: $501.87
You Save: $128.56 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Ignition Switch; Cylinder & Keys
- Replaces: GPYB-76-14X, GPYB-76-14XA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Cylinder Part Number: GE4T-64-09YB-80
$4.51 MSRP: $6.02
You Save: $1.51 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Glove Lid; Lock Cylinder
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2008 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Cylinder Part Number: GE4T-64-09YB-00
$8.29 MSRP: $11.05
You Save: $2.76 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Glove Lid; Cylinder
- Replaces: GE4T-64-09YB
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2013 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Ignition Lock Cylinder Part Number: GSYB-76-14X
$155.50 MSRP: $207.38
You Save: $51.88 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Ignition Switch
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | i, S | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Ignition Lock Cylinder Part Number: GSYN-76-14X
$155.73 MSRP: $207.68
You Save: $51.95 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Ignition Switch
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | i, S | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Cylinder & Keys Part Number: GS4D-09-010D
$233.29 MSRP: $306.21
You Save: $72.92 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Set
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | i, S | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Ignition Lock Cylinder Part Number: FEY6-76-14XB
Product Specifications
- Other Name: Key Sub Set, Ignition Switch; Cylinder & Keys
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Cylinder & Keys Part Number: GEA2-09-010B
Product Specifications
- Other Name: Key Set
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | i, S | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Ignition Lock Cylinder Part Number: GEY2-76-14XA
Product Specifications
- Other Name: Key Sub Set, Ignition Switch
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | i, S | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Ignition Lock Cylinder Part Number: GKYA-76-14X
Product Specifications
- Other Name: Key Sub Set, Ignition Switch; Cylinder & Keys
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2005 Mazda 6 | i, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Ignition Lock Cylinder Part Number: GKYE-76-14X
Product Specifications
- Other Name: KEY SET,IGN (A/T); Ignition Lock Cylinder
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2005 Mazda 6 | i, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Ignition Lock Cylinder Part Number: GPYA-76-14XA
Product Specifications
- Other Name: Key Sub Set, Ignition Switch
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2007 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Cylinder & Keys Part Number: GS3L09010B
Product Specifications
- Other Name: Key Set
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | i, S | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Cylinder & Keys Part Number: GS4B09010B
Product Specifications
- Other Name: Key Set
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | i, S | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Ignition Lock Cylinder Part Number: GSYC-76-14XA
Product Specifications
- Other Name: Key Sub Set, Ignition Switch
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | i, S | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS

Mazda 6 Ignition Lock Cylinder

Looking for Ignition Lock Cylinder with proven quality? Choose OEM Ignition Lock Cylinder. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda 6 parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine 6 part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda 6 Ignition Lock Cylinder Parts and Q&A

Ignition Lock Cylinder
GPYB-76-14XB
Q: How to replace the ignition lock cylinder and ignition switch on Mazda 6?
A:
Unscrew the cable off the negative side of the battery. Take out knee bolster trim panel, knee bolster, upper and lower steering columns covers, then bend the steering column to the lowest. It should be done with caution since doing both of them at the same time of taking out the ignition switch and key lock cylinder may result in damage of the steering column. Unscrew the electrical connector the ignition switch, then screw out the mounting screw and press the release tabs so that the ignition switch can be pulled off the steering column. Installation of the switch is the opposite of its removal and is best installed in a snapping manner. The ignition switch and key lock cylinder should also be taken with caution. 1. Turn ignition key on 2008 and earlier models or ACC off 2009 and later models. Depress the release button of the key lock cylinder with a proper tool and take out the key lock cylinder. In order to install the key lock cylinder, it is necessary to insert the key lock cylinder into the housing of the lock cylinder and press it inside until it clicks. Ensure that the ignition switch is working properly in the OFF, ACC, RUN and START positions with installation being the opposite of uninstallation. It is not necessary to remove the lock cylinder illumination ring in order to replace the lock cylinder. Unscrew the electrical connector out of the illumination ring, unscrew the lock tabs and take out the illumination ring. Installation is its counterpart, and it is opposite to remove, and the ring should be able to be placed.
Cylinder & Keys
GS4D-09-010D
Q: How to disconnect and remove the Ignition Lock Cylinder and Trunk Lid Latch on Mazda 6?
A:
Disconnect the cable from the negative battery terminal and remove the trunk lid trim panel. Rotate the trunk lid actuator rod mounting clip and disconnect the rod from the trunk lid key lock cylinder assembly, then disconnect the electrical connector from the lock cylinder if equipped. Remove the mounting nuts and maneuver the lock cylinder out from the trunk lid, with installation being the reverse of removal. Next, disconnect the actuator rod from the trunk lid lock cylinder and the electrical connector from the trunk lid latch. Remove the latch mounting bolts and take out the latch, with installation again being the reverse of removal.