How to remove and install the Door Latch Assembly,Exterior Door Handle,Interior Door Handle and Door Lock Cylinder on Mazda 6?

Remove the door window glass and disconnect the cable from the negative battery terminal. Next, remove the door trim panel. For the outside door handle, take off the access hole cover and mounting screw, noting that on 2009 and later models, a stop prevents the screw from being removed. Rotate the latch rod and lock rod clips back to disconnect the rods from the outer handle, then pull the handle outwards. For 2008 and earlier models, remove the cover from the outside handle, and pull the handle out and to the rear to disengage it from the handle reinforcement inside the door. Remove the outside handle support mounting bolt from inside the door and take out the support. Inspect the outside door handle seals and replace them if they are cracked, torn, or deteriorated. Installation is the reverse of removal. For the inside door handle, pull the locking tab back, slide the shaft up, and detach the handle assembly from the door module, then disconnect the door lock cable from the inside door handle cable, with installation being the reverse of removal. To access the door latch, remove the outside door handle and disconnect the inside door handle and cables. Remove the door module mounting screws and take out the module, which includes the power window motor and window regulator. Disconnect the harness connector from the latch lock actuator if it wasn't done earlier, then disconnect the lock rod and latch rod from the door latch. Remove the door latch mounting screws and guide the latch assembly from the door, with installation being the reverse of removal. For the door lock cylinder on 2008 and earlier models, remove the door latch, rotate the lock cylinder counterclockwise until the tab fits into the notch opening, and pull the key lock cylinder out through the door, with installation being the reverse of removal. For 2009 and later models, remove the outside door handle, take out the access plug from the end of the door, and from the inside, remove the key lock rod clip and disconnect the rod from the key cylinder. Loosen the screw through the access hole from the end of the door, press the release tab on the inside of the door handle, and remove the lock cylinder from the door. Finally, separate the exterior trim cap from the key lock cylinder using a small screwdriver to disengage the tabs, with installation being the reverse of removal.

Genuine Mazda 6 Interior Door Handle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

34 Interior Door Handles found

View related parts
Mazda 6 Handle, Inside Part Number: GBFN-59-330
$47.16 MSRP: $62.90
You Save: $15.74 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2018-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GBFN-58-330
$48.58 MSRP: $64.77
You Save: $16.19 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Right), Inner; Handle Inside
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2018-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GHP9-59-330G
$54.79 MSRP: $73.07
You Save: $18.28 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Replaces: GHP9-59-330D, GHP9-59-330C, GHP9-59-330E
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2017 Mazda 6 | Grand Touring, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: C235-58-330A-02
$25.69 MSRP: $34.26
You Save: $8.57 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Right), Inner; Handle Inside
- Position: Passenger Side
- Replaces: C235-58-330-02
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mazda 6 | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: C235-59-330A-02
$27.84 MSRP: $37.12
You Save: $9.28 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Replaces: C235-59-330-02
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mazda 6 | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GEA3-73-330A-02
$41.59 MSRP: $55.46
You Save: $13.87 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Left), Inner-Rear Door; Handle Inside
- Position: Driver Side
- Replaces: GEA3-73-330-02
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GEA4-72-330-02
$41.76 MSRP: $55.69
You Save: $13.93 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Right), Inner-Rear Door; Handle Inside
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GEA4-58-330-02
$41.78 MSRP: $55.71
You Save: $13.93 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Right), Inner; Handle Inside
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GEA3-72-330A-02
$42.63 MSRP: $56.85
You Save: $14.22 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Right), Inner-Rear Door; Handle Inside
- Position: Passenger Side
- Replaces: GEA3-72-330-02
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GS3T-59-330-30
$42.76 MSRP: $57.03
You Save: $14.27 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Replaces: GS3T-59-330A-30
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GSY2-59-330
$43.28 MSRP: $57.72
You Save: $14.44 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Replaces: GS3L-59-330B-74, GS3L-59-330A-74
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GEA4-59-330-02
$45.09 MSRP: $60.13
You Save: $15.04 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GS3T-59-330-02
$46.15 MSRP: $61.55
You Save: $15.40 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Replaces: GS3T-59-330A-02
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GHP9-58-330B
$51.13 MSRP: $68.18
You Save: $17.05 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Right), Inner; Handle Inside
- Position: Passenger Side
- Replaces: GHP9-58-330, GHP9-58-330A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2017 Mazda 6 | Grand Touring, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GJ6A-59-330E
$65.23 MSRP: $86.98
You Save: $21.75 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Replaces: GJ6A-59-330D, GJ6A-59-330C
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2005 Mazda 6 | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GSY1-59-330
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GSY1-58-330
Product Specifications
- Other Name: Handle(Right), Inner; Handle Inside
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GSY0-59-330
Product Specifications
- Other Name: Handle(Left), Inner; Handle Inside
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GS3T-73-330-02
Product Specifications
- Other Name: Handle Left, Inner Rear Door; Handle Inside
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Handle, Inside Part Number: GS3T-72-330-02
Product Specifications
- Other Name: Handle Right, Inner Rear Door; Handle Inside
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS

| Page 1 of 2 |Next >

1-20 of 34 Results

Mazda 6 Interior Door Handle

The Interior Door Handle of the Mazda 6 is the component that is operated to trigger the door's latch so that a door can be opened from the inside. Accessible with ease, the part is designed to disengage the hook securing the door to the latch in the frame to allow for a switch from the locked to open position. The handle is subject to constant mechanical stress and repetitive movement, where daily use can gradually damage its moving surfaces. Over time, the lever can develop scratches, and a cosmetic mark on the driver side, where it always makes contact, is no big deal. All Mazda models have a driver side handle surface that shows this kind of wear. It is just part of the car's operation from getting in and out. Even though the rest of the cabin trim is fine, it can detract from the overall look of things. Constant pulling could speed up fatigue in the linkage attached to the latch assembly, meaning if that linkage weakens or something happens to a related part inside the latch, the door may not unlock or open properly to let people out of the vehicle. When the mechanism is functioning properly, a light pull on the Interior Door Handle will separate the hook from the striker and allow the panel to swing away without much effort. Since reliable egress is a fundamental expectation regarding safety, the task of the handle is essential every time the vehicle is stopped or a panic exit situation arises. Owners of the Mazda 6 will benefit from an Interior Door Handle made for frequent use. Moreover, so long as your Mazda cabin is well-maintained, it can remain both functional and tidy looking.

Looking for Interior Door Handle with proven quality? Choose OEM Interior Door Handle. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda 6 parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine 6 part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda 6 Interior Door Handle Parts and Q&A

Handle, Inside
GS3L-73-330A-02
Q:
How to remove and install the Door Latch Assembly,Exterior Door Handle,Interior Door Handle and Door Lock Cylinder on Mazda 6?
A:
Remove the door window glass and disconnect the cable from the negative battery terminal. Next, remove the door trim panel. For the outside door handle, take off the access hole cover and mounting screw, noting that on 2009 and later models, a stop prevents the screw from being removed. Rotate the latch rod and lock rod clips back to disconnect the rods from the outer handle, then pull the handle outwards. For 2008 and earlier models, remove the cover from the outside handle, and pull the handle out and to the rear to disengage it from the handle reinforcement inside the door. Remove the outside handle support mounting bolt from inside the door and take out the support. Inspect the outside door handle seals and replace them if they are cracked, torn, or deteriorated. Installation is the reverse of removal. For the inside door handle, pull the locking tab back, slide the shaft up, and detach the handle assembly from the door module, then disconnect the door lock cable from the inside door handle cable, with installation being the reverse of removal. To access the door latch, remove the outside door handle and disconnect the inside door handle and cables. Remove the door module mounting screws and take out the module, which includes the power Window Motor and Window Regulator. Disconnect the harness connector from the latch lock actuator if it wasn't done earlier, then disconnect the lock rod and latch rod from the door latch. Remove the door latch mounting screws and guide the latch assembly from the door, with installation being the reverse of removal. For the door lock cylinder on 2008 and earlier models, remove the door latch, rotate the lock cylinder counterclockwise until the tab fits into the notch opening, and pull the key lock cylinder out through the door, with installation being the reverse of removal. For 2009 and later models, remove the outside door handle, take out the access plug from the end of the door, and from the inside, remove the key lock rod clip and disconnect the rod from the key cylinder. Loosen the screw through the access hole from the end of the door, press the release tab on the inside of the door handle, and remove the lock cylinder from the door. Finally, separate the exterior trim cap from the key lock cylinder using a small screwdriver to disengage the tabs, with installation being the reverse of removal.

Related Mazda 6 Parts

Browse by Year

2021 Interior Door Handle 2020 Interior Door Handle 2019 Interior Door Handle 2018 Interior Door Handle 2017 Interior Door Handle 2016 Interior Door Handle 2015 Interior Door Handle 2014 Interior Door Handle 2013 Interior Door Handle 2012 Interior Door Handle 2011 Interior Door Handle 2010 Interior Door Handle 2009 Interior Door Handle 2008 Interior Door Handle 2007 Interior Door Handle 2006 Interior Door Handle 2005 Interior Door Handle 2004 Interior Door Handle 2003 Interior Door Handle

Genuine Mazda 6 Interior Door Handle

34 Interior Door Handles found

Mazda 6 Handle, Inside Part Number: GBFN-59-330

Mazda 6 Handle, Inside Part Number: GBFN-58-330

Mazda 6 Handle, Inside Part Number: GHP9-59-330G

Mazda 6 Handle, Inside Part Number: C235-58-330A-02

Mazda 6 Handle, Inside Part Number: C235-59-330A-02

Mazda 6 Handle, Inside Part Number: GEA3-73-330A-02

Mazda 6 Handle, Inside Part Number: GEA4-72-330-02

Mazda 6 Handle, Inside Part Number: GEA4-58-330-02

Mazda 6 Handle, Inside Part Number: GEA3-72-330A-02

Mazda 6 Handle, Inside Part Number: GS3T-59-330-30

Mazda 6 Handle, Inside Part Number: GSY2-59-330

Mazda 6 Handle, Inside Part Number: GEA4-59-330-02

Mazda 6 Handle, Inside Part Number: GS3T-59-330-02

Mazda 6 Handle, Inside Part Number: GHP9-58-330B

Mazda 6 Handle, Inside Part Number: GJ6A-59-330E

Mazda 6 Handle, Inside Part Number: GSY1-59-330

Mazda 6 Handle, Inside Part Number: GSY1-58-330

Mazda 6 Handle, Inside Part Number: GSY0-59-330

Mazda 6 Handle, Inside Part Number: GS3T-73-330-02

Mazda 6 Handle, Inside Part Number: GS3T-72-330-02

Mazda 6 Interior Door Handle

Mazda 6 Interior Door Handle Parts and Q&A

Related Mazda 6 Parts

Browse by Year