How to replace the window motor and window regulator assembly on Mazda 6?

To replace the power window motor, first disconnect the cable from the negative battery terminal, then remove the door trim panel. Next, disconnect the electrical connector from the regulator motor and secure the window in place with tape. Remove the three regulator motor mounting screws and take out the motor, with installation being the reverse of removal. For the regulator assembly, begin by removing the door trim panel and the front door speaker, followed by the door glass. If the vehicle has power windows, remove the power window motor. Then, take off the regulator mounting nuts, insert one hand through the speaker hole to rotate the window regulator drum housing clockwise from the inside, and disconnect the tabs from the door module. Remove the window regulator through the speaker hole, install the new regulator through the same hole, and ensure the drum housing locks into the door module while preventing the cable from un-spooling. Finally, tighten the regulator mounting nuts or bolts securely, with the remainder of the installation being the reverse of removal.

Genuine Mazda 6 Window Motor

Window Lift Motor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Window Motors found

View related parts
Mazda 6 Window Motor Part Number: D01G-58-58XB
$96.90 MSRP: $129.23
You Save: $32.33 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor(Right), Window
- Position: Right
- Replaces: D01G-58-58XA, D01G-58-58X
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2017 Mazda 6 | Grand Touring, i, S, Sport, Touring | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Window Motor Part Number: D01G-59-58XB
$101.14 MSRP: $134.88
You Save: $33.74 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor(Left), Window
- Position: Left
- Replaces: D01G-59-58X, D01G-59-58XA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2017 Mazda 6 | Grand Touring, i, S, Sport, Touring | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Window Motor Part Number: D651-58-58XB
$103.34 MSRP: $137.80
You Save: $34.46 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor(Right), Window
- Position: Right
- Replaces: D651-58-58X, D651-58-58XA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2021, 2009-2010 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, i, S, Signature, Sport, Touring | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Window Motor Part Number: D651-59-58XB
$104.15 MSRP: $138.89
You Save: $34.74 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor Left, Window
- Position: Left
- Replaces: D651-59-58XA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, i, S, Signature, Sport, Touring | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Motor Part Number: GJ6A-58-58XC
$207.91 MSRP: $277.28
You Save: $69.37 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor, Window; Motor
- Replaces: GJ6A-58-58XA, GJ6A-58-58XB
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2008 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Motor Part Number: G22C-58-58XF
$211.06 MSRP: $281.48
You Save: $70.42 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor, Window; Motor
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Motor Part Number: G22C-59-58XC
$220.53 MSRP: $294.09
You Save: $73.56 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor, Window; Motor
- Replaces: G22C-59-58XB, G22C-59-58XA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2008 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Motor Part Number: GJ6A-59-58XF
$220.53 MSRP: $294.09
You Save: $73.56 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Motor, Window; Motor
- Replaces: GJ6A-59-58XE
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2008 Mazda 6 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

Mazda 6 Window Motor

The Window Motor also allows the occupants of the Mazda 6 car to breathe in fresh air or close the windows against rain without having to crank the windows by hand, with the Window Motor allowing one-touch operation on all door glass. This Window Motor is located within the door panel, and it is connected to the regulator, and, when the switch is pushed, it is fed a current that causes it to rotate its gears to push the window either up or down. Similar to most modern Mazda models, it uses an all-electric design as opposed to the older hand cranks, and therefore it has only one main style throughout the series with no arbitrary variations to follow. When the glass begins to crawl upwards, moves in the opposite direction, is unable to move at all, or does not move though a whirring sound is heard, drivers immediately perceive something wrong. These are indications of a weak motor, an out-of-phase regulator, or a dead circuit between the switch and the unit. Mazda 6 vehicles built since launch share the same simple setup, so testing of functions is easy since the motor is powered directly by the switch and nothing more is in the way to cause any complications. Frequent use keeps the components oily; however, neglecting strange sounds can allow grime or wear to spread. This will ensure that the Mazda 6 power window system is treated with the appropriate urgency to maintain cabin comfort and ensure that all rides are dry, safe, and enjoyable without having to carry out extensive repairs to the Window Motor.

Looking for Window Motor with proven quality? Choose OEM Window Motor. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda 6 parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine 6 part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda 6 Window Motor Parts and Q&A

Motor
GJ6A-58-58XC
Q: How to replace the window motor and window regulator assembly on Mazda 6?
A:
To replace the power window motor, first disconnect the cable from the negative battery terminal, then remove the door trim panel. Next, disconnect the electrical connector from the regulator motor and secure the window in place with tape. Remove the three regulator motor mounting screws and take out the motor, with installation being the reverse of removal. For the regulator assembly, begin by removing the door trim panel and the front door speaker, followed by the door glass. If the vehicle has power windows, remove the power window motor. Then, take off the regulator mounting nuts, insert one hand through the speaker hole to rotate the window regulator drum housing clockwise from the inside, and disconnect the tabs from the door module. Remove the window regulator through the speaker hole, install the new regulator through the same hole, and ensure the drum housing locks into the door module while preventing the cable from un-spooling. Finally, tighten the regulator mounting nuts or bolts securely, with the remainder of the installation being the reverse of removal.