How to remove and install the Door Latch Assembly,Exterior Door Handle,Interior Door Handle and Door Lock Cylinder on Mazda 3?

To begin, roll the window all the way up and disconnect the cable from the negative battery terminal. Next, remove the door trim panel and the outside handle access panel. Remove the sound pad mounting nut from the stud bolt, then take out the pad and the stud bolt. For 2010 and later models, disconnect the electrical connector to the door handle bracket for the keyless entry antenna. Rotate the rod clip back and disconnect the rod from the outer handle, then pull the handle outwards and remove the cover from the outside handle. To remove the outside door handle, pull it out of the door and to the rear to disengage it from the handle reinforcement inside the door. Inspect the outside door handle seals and replace them if they are cracked, torn, or otherwise deteriorated. The installation process is the reverse of removal. For the inside door handle, pull the locking tab back, slide the shaft up, and detach the handle assembly from the door module. Disconnect the door lock cable from the inside door handle cable, with installation being the reverse of removal. For the door latch, remove the outside door handle lever, carefully pry up the window/door trim from the outside of the door, and remove the window glass. Remove the door speaker by disconnecting all electrical connectors and harnesses, then disconnect the inside door handle and cables. Remove the door module mounting fasteners and take out the module, noting that the power window motor and window regulator are attached to it. Disconnect the harness connector from the latch lock actuator, disconnect the lock rod from the door latch, and remove the door latch mounting screws to guide the latch assembly from the door, with installation being the reverse of removal. For the door lock cylinder on 2009 and earlier models, remove the outside door handle and door latch, rotate the lock cylinder counterclockwise until the tab fits into the notch opening, and pull the key lock cylinder out through the door, with installation being the reverse of removal. For 2010 and later models, remove the power window regulator and the outside door handle, take out the access plug from the end of the door and the access hole plug on the face of the door, remove the door lock link bracket mounting nut and bracket, loosen the screw through the access hole, disconnect the key rod clip and rod from the key assembly, disengage the release tab on the inside of the door handle to remove the lock cylinder, and separate the exterior trim cap from the key cylinder using a small screwdriver to disengage the tabs, with installation being the reverse of removal.

How to remove and install a door lock cylinder on Mazda 929?

Removing and installing the door lock To install and remove the door lock, begin by removing the regulator handle, arm rest and other parts. The trim panel and watershield should be removed next. Take off the bolts which attach the handle to the inner and remove the inner handle cylinder. The Zoom way is to completely lift the glass and remove the remote control rod of the lock. Then screw the door lock off by removing the screws and remove the door lock. Then take off a retainer which is the lock cylinder to the inner panel and pull out the lock cylinder. To install in reverse order of these steps.

Genuine Mazda Door Lock Cylinder

Door Lock Cylinder Tumbler

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

145 Door Lock Cylinders found

View related parts
Mazda Cylinder & Keys Part Number: VAY0-76-220A
$44.35 MSRP: $59.14
You Save: $14.79 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key, Lock Cylinder
- Position: Driver Side
- Replaces: VAY0-76-220
Fits the following Mazda Models:
- CX-50 | 2023-2025 | 2.5 S, 2.5 Turbo, Hybrid Preferred, Hybrid Premium | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: TDY6-76-220
$84.40 MSRP: $112.56
You Save: $28.16 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key
- Position: Driver Side
Fits the following Mazda Models:
- CX-9 | 2011-2015 | Grand Touring, Sport, Touring | 6 Cyl 3.7 L GAS
View related parts
Mazda Lock Cylinder Part Number: KBY0-76-220
$80.89 MSRP: $107.88
You Save: $26.99 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key
- Position: Driver Side
Fits the following Mazda Models:
- CX-5 | 2017-2023 | 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: KBY2-76-220
$85.24 MSRP: $113.68
You Save: $28.44 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Set Left; Cylinder & Key
- Position: Driver Side
Fits the following Mazda Models:
- CX-5 | 2021-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: BJYE-76-210B
$16.01 MSRP: $126.84
You Save: $110.83 (88%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set (Right) Door; Cylinder & Key
- Position: Passenger Side
- Replaces: BJYE-76-210A
Fits the following Mazda Models:
- Protege | 1999-2003 | DX, ES, LX, MP3, Mazdaspeed | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Protege5 | 2002-2003 | Base | 4 Cyl 2.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: LCY2-76-220E
$16.87 MSRP: $129.93
You Save: $113.06 (88%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Set Left; Key Cylinder
- Position: Driver Side
- Replaces: LCY2-76-220C, LCY2-76-220D
Fits the following Mazda Models:
- MPV | 2000-2003 | DX, ES, LX | 6 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Cylinder & Keys Gasket Part Number: KA78-62-493
$12.70 MSRP: $16.94
You Save: $4.24 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gasket
Fits the following Mazda Models:
- 626 | 1998-2002 | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: DGY1-76-220
$50.78 MSRP: $67.72
You Save: $16.94 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key
- Position: Driver Side
Fits the following Mazda Models:
- CX-30 | 2020-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: GSYL-76-220
$57.19 MSRP: $76.26
You Save: $19.07 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key
- Position: Driver Side
Fits the following Mazda Models:
- 6 | 2009-2013 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda Lock Cylinder Part Number: D3Y0-76-220
$61.84 MSRP: $82.46
You Save: $20.62 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key
Fits the following Mazda Models:
- 6 | 2003-2006 | Mazdaspeed, S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: GKYA-76-230A
$68.59 MSRP: $91.48
You Save: $22.89 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
- Replaces: GKYA-76-230
Fits the following Mazda Models:
- 6 | 2003-2008 | Mazdaspeed, S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Cylinder & Keys Part Number: B2YH-76-260
$70.94 MSRP: $94.60
You Save: $23.66 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Lift Gate; Cylinder & Key
Fits the following Mazda Models:
- Protege5 | 2002-2003 | Base | 4 Cyl 2.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: BHY0-76-220
$71.09 MSRP: $94.80
You Save: $23.71 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door
- Position: Driver Side
Fits the following Mazda Models:
- 3 | 2014-2018 | Grand Touring, I Sport, I Touring, Sport, Touring, i Grand Touring, i SV, s Grand Touring, s Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: BGY0-76-220
$73.99 MSRP: $98.66
You Save: $24.67 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door
- Position: Driver Side
Fits the following Mazda Models:
- 3 | 2022-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: B2YD-76-230A
$76.08 MSRP: $101.46
You Save: $25.38 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
Fits the following Mazda Models:
- Protege | 1999-2003 | DX, ES, LX, MP3, Mazdaspeed | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Protege5 | 2002-2003 | Base | 4 Cyl 2.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: TA52-76-210F
$76.86 MSRP: $102.51
You Save: $25.65 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Right), Door; Cylinder & Key
- Position: Passenger Side
Fits the following Mazda Models:
- Millenia | 1995-2002 | Base, L, Millennium Edition, S | 6 Cyl 2.3 L GAS, 6 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: TKY0-76-220
$79.33 MSRP: $105.79
You Save: $26.46 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key
- Position: Driver Side
Fits the following Mazda Models:
- CX-9 | 2016-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: EHY4-76-220
$81.31 MSRP: $108.45
You Save: $27.14 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key
- Position: Driver Side
Fits the following Mazda Models:
- CX-7 | 2007-2012 | Grand Touring, SV, Sport, Touring | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: DKY1-76-220
$88.01 MSRP: $117.37
You Save: $29.36 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key
- Position: Driver Side
Fits the following Mazda Models:
- CX-3 | 2016-2021 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: BAY8-76-220
$90.25 MSRP: $120.35
You Save: $30.10 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set(Left), Door; Cylinder & Key
- Position: Driver Side
Fits the following Mazda Models:
- 3 | 2008-2009 | Mazdaspeed, S, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
- 5 | 2012-2015 | Grand Touring, Sport, Touring | 4 Cyl 2.5 L GAS

| Page 1 of 8 |Next >

1-20 of 145 Results

Mazda Door Lock Cylinder

Mazda Door Lock Cylinder offers a mechanical protection that is always reliable and allows drivers to lock or unlock their vehicle with a simple turn of a key, providing security even in the event of electronic failure. Mazda has long been recognized for its combination of spirited handling, efficient Skyactiv powertrains, bold Kodo styling and forward-thinking i-Activsense safety features that make travel in daily life fun and reassuring. The brand gets the balance right between fuel-saving engineering and fun road feel, and with an increasing use of electric and mild hybrid tech, it's clear that Mazda has plans to keep the fun alive while reducing emissions. Loyal fans appreciate the way Mazda models ranging from compact hatchbacks to roomy SUVs share a confident driving character that is born from strict chassis tuning and rigorous real-world testing on a variety of terrain. Within this dynamic lineup, the Door Lock Cylinder is a small but important part that fulfills the company's commitment to reliability. The Door Lock Cylinder connects the physical key to internal latch levers, such that a single smooth twist provides a direct motion to lock or release the door, providing a tactile backup when remote fobs run out of power. Because Mazda carries this sturdy part throughout their range, owners have access to peace of mind no matter the weather or battery charge, keeping every trip simple and secure.

You'll get great performance and real durability when you pick genuine OEM Door Lock Cylinder. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Door Lock Cylinder Parts and Q&A

Lock Cylinder
BAY8-76-220
Q:
How to remove and install the Door Latch Assembly,Exterior Door Handle,Interior Door Handle and Door Lock Cylinder on Mazda 3?
A:
To begin, roll the window all the way up and disconnect the cable from the negative battery terminal. Next, remove the door trim panel and the outside handle access panel. Remove the sound pad mounting nut from the stud bolt, then take out the pad and the stud bolt. For 2010 and later models, disconnect the electrical connector to the door handle bracket for the keyless entry antenna. Rotate the rod clip back and disconnect the rod from the outer handle, then pull the handle outwards and remove the cover from the outside handle. To remove the outside door handle, pull it out of the door and to the rear to disengage it from the handle reinforcement inside the door. Inspect the outside door handle seals and replace them if they are cracked, torn, or otherwise deteriorated. The installation process is the reverse of removal. For the inside door handle, pull the locking tab back, slide the shaft up, and detach the handle assembly from the door module. Disconnect the door lock cable from the inside door handle cable, with installation being the reverse of removal. For the door latch, remove the outside door handle lever, carefully pry up the window/door trim from the outside of the door, and remove the window glass. Remove the door speaker by disconnecting all electrical connectors and harnesses, then disconnect the inside door handle and cables. Remove the door module mounting fasteners and take out the module, noting that the power window motor and window regulator are attached to it. Disconnect the harness connector from the latch lock actuator, disconnect the lock rod from the door latch, and remove the door latch mounting screws to guide the latch assembly from the door, with installation being the reverse of removal. For the door lock cylinder on 2009 and earlier models, remove the outside door handle and door latch, rotate the lock cylinder counterclockwise until the tab fits into the notch opening, and pull the key lock cylinder out through the door, with installation being the reverse of removal. For 2010 and later models, remove the power window regulator and the outside door handle, take out the access plug from the end of the door and the access hole plug on the face of the door, remove the door lock link bracket mounting nut and bracket, loosen the screw through the access hole, disconnect the key rod clip and rod from the key assembly, disengage the release tab on the inside of the door handle to remove the lock cylinder, and separate the exterior trim cap from the key cylinder using a small screwdriver to disengage the tabs, with installation being the reverse of removal.
Lock Cylinder
HF05-76-230
Q:
How to remove and install a door lock cylinder on Mazda 929?
A:
Removing and installing the door lock To install and remove the door lock, begin by removing the regulator handle, arm rest and other parts. The trim panel and watershield should be removed next. Take off the bolts which attach the handle to the inner and remove the inner handle cylinder. The Zoom way is to completely lift the glass and remove the remote control rod of the lock. Then screw the door lock off by removing the screws and remove the door lock. Then take off a retainer which is the lock cylinder to the inner panel and pull out the lock cylinder. To install in reverse order of these steps.