How to remove and install the rear Drive Shaft on Mazda B2200?

Installation of the driveshaft and the removal of the same in the Navajo model requires that the negative battery cable is disconnected and the vehicle is raised safely. Mark the driveshaft yoke against the axle flange and then unhook it, after which the driveshaft needs to be disconnected to the axle companion flange and the back end of the transfer case and then the driveshaft itself should be removed. To install, fit driveshaft with the slip yoke facing the front, insert the bolts and loosen them to 41-55 ft. lbs. make sure the index mark on rear yoke coincides with the index mark on axle companion flange. In Pickup and MPV models, matchmark the rear U-joint and the rear companion flange, unbolt the U-joint, and dismount the center support bearing bracket and withdraws the driveshaft out of the transmission and stuffs the rear seal opening. Installation is the opposite of removal and match marks are to be aligned and the rear companion flange bolts tightened to 39-47 ft. lbs and the center bearing bracket nuts tightened to 27-38 ft. lbs. In the case of U- joint replacement, the operations performed are similar to the one-cardan U-joint. To solve the issue of driveshaft balancing, vibrations can be used to show an indication of an imbalance and this imbalance can be due to faulty universal joints or the wrong angle that is used, not necessarily the driveshaft itself. Check, check, Clean, Check: To check, raise the vehicle, check the propeller shaft, check the universal joints and clamp bolts, and check universal joints and clamp bolts. Trace the shaft and drive the vehicle to determine the intensity and speed of vibration and may use screw clamps to reduce the vibration. In case there are unacceptable vibration, repeat the procedure on the front part of the propeller shaft. To check the run-out, clean up surface of the shaft, screw a dial indicator perpendicular to the shaft and check at given points and change the propeller shaft when the measurements are more than 0.035 inch in the case of Navajo models and 0.016 inch in the case of Pickup and MPV models.

How to remove and install the drive shaft and universal joint on Mazda 929?

To install and uninstall the rear driveshaft on different models, you will have to start by lifting the rear end of the car safely placing it on jackstands. Mark the drive shaft and pinion flanges so that they fit during reassembly. It can be done by loosening the bolts between the driveshaft and the pinion flange and in the case of the 929 model, the center bearing support bracket is unbolted and then the lower part of the driveshaft is lowered and the front part of the driveshaft can be slid out of the transmission. To ensure that there is no leakage of fluid, seal the transmission hole with an appropriate technique. To install it, insert the front part of the drive shaft into the transmission, lift the rear part onto the pinion flange, and make sure that the matchmarks align properly then tighten the flange bolts up to definite values. In the case of RX-7, the driveshaft should be installed at the same location as indicated not to cause vibrations and the tightening of the bolts must be done as indicated by the model. In performing the overhaul of the joint, matchmark the yoke and driveshaft, remove the bearing snaprings and drive out the bearing cups with great care. Check the wear of the spider, measure its diameter and change when needed. Installation Prepare the bearers by stuffing the bearing cups with grease, attaching the rollers and dust seals, and making sure that the U-joint has slight drag and is not binding. Lastly, test the U-joint assembly to operations.

Genuine Mazda Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

63 Drive Shafts found

View related parts
Mazda Drive Shaft Part Number: KH50-25-100B
$722.52 MSRP: $987.25
You Save: $264.73 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
- Replaced by: KH50-25-100C
Fits the following Mazda Models:
- CX-50 | 2023-2025 | 2.5 S, 2.5 Turbo, Hybrid Preferred, Hybrid Premium | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
View related parts
Mazda Drive Shaft Part Number: KF14-25-100
$1078.28 MSRP: $1473.37
You Save: $395.09 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
Fits the following Mazda Models:
- CX-30 | 2021-2023 | 2.5 Turbo | 4 Cyl 2.5 L GAS
View related parts
Mazda Drive Shaft Part Number: PA48-25-100
$529.47 MSRP: $711.79
You Save: $182.32 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller; Drive Shaft Assembly
Fits the following Mazda Models:
- MX-5 Miata | 2016-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF GT, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Drive Shaft Part Number: PA47-25-100
$568.32 MSRP: $764.02
You Save: $195.70 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller; Drive Shaft Assembly
Fits the following Mazda Models:
- MX-5 Miata | 2016-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF GT, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Drive Shaft Part Number: PA40-25-100
$508.60 MSRP: $683.73
You Save: $175.13 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller-Front
Fits the following Mazda Models:
- RX-8 | 2006-2011 | 40th Anniversary Edition, Base, Grand Touring, R3, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Drive Shaft Part Number: KH40-25-100A
$854.13 MSRP: $1167.09
You Save: $312.96 (27%)
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
- Replaces: KH40-25-100
Fits the following Mazda Models:
- CX-9 | 2016-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda Drive Shaft Part Number: KH01-25-100A
$983.30 MSRP: $1343.57
You Save: $360.27 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
Fits the following Mazda Models:
- CX-5 | 2013-2016 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Drive Shaft Part Number: KH30-25-100B
$967.47 MSRP: $1321.95
You Save: $354.48 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
Fits the following Mazda Models:
- CX-3 | 2016-2021 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Drive Shaft Part Number: KH03-25-100
$983.30 MSRP: $1343.57
You Save: $360.27 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
Fits the following Mazda Models:
- CX-5 | 2017-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda Drive Shaft Part Number: KF03-25-100B
$1021.82 MSRP: $1396.20
You Save: $374.38 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
- Replaced by: KF03-25-100C
Fits the following Mazda Models:
- 3 | 2020-2025 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Drive Shaft Part Number: KF03-25-100A
$1021.82 MSRP: $1396.20
You Save: $374.38 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
- Replaced by: KF03-25-100C
Fits the following Mazda Models:
- 3 | 2019-2020 | Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Shaft, Propeller Part Number: CF01-25-100B
$1025.62 MSRP: $1401.40
You Save: $375.78 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SHAFT,PROPELLER; Drive Shaft, Drive Shaft Assembly
Fits the following Mazda Models:
- CX-70 | 2025 | PHEV, Turbo, Turbo S | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
- CX-90 | 2024-2025 | PHEV, Turbo, Turbo S | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
View related parts
Mazda Drive Shaft Part Number: KF12-25-100B
$1141.32 MSRP: $1559.49
You Save: $418.17 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
- Replaces: KF12-25-100A, KF12-25-100
Fits the following Mazda Models:
- CX-30 | 2020-2023 | 2.5 S, 2.5 S Carbon Edition, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda SHAFT,PROPELLER Part Number: KF06-25-100A
$1141.32 MSRP: $1559.49
You Save: $418.17 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Drive Shaft
- Replaces: KF05-25-100, KF06-25-100
Fits the following Mazda Models:
- 3 | 2021-2025 | 2.5 Carbon Turbo, 2.5 Turbo, 2.5 Turbo Premium Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda Drive Shaft Part Number: KF05-25-100
$1141.32 MSRP: $1559.49
You Save: $418.17 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller
- Replaced by: KF06-25-100A
Fits the following Mazda Models:
- 3 | 2021-2025 | 2.5 Carbon Turbo, 2.5 Turbo, 2.5 Turbo Premium Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda Shaft, Propeller Part Number: PFZ5-25-10XB
$1345.84 MSRP: $1838.95
You Save: $493.11 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SHAFT,PROPELLER; Drive Shaft
- Replaces: PFZ5-25-10XA, PFZ5-25-10X
Fits the following Mazda Models:
- CX-70 | 2025 | Turbo, Turbo S | 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
- CX-90 | 2024-2025 | Turbo, Turbo S | 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
View related parts
Mazda Shaft, Propeller Part Number: PFZ1-25-10XB
$1345.84 MSRP: $1838.95
You Save: $493.11 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SHAFT,PROPELLER; Drive Shaft
- Replaces: PFZ1-25-10X, PFZ1-25-10XA
Fits the following Mazda Models:
- CX-70 | 2025 | PHEV | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
- CX-90 | 2024-2025 | PHEV | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mazda Drive Shaft Part Number: ZZP2-25-100A
$109.30 MSRP: $143.46
You Save: $34.16 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller; Drive Shaft Assembly
Fits the following Mazda Models:
- B2300 | 2001-2009 | Base, SE, SX | 4 Cyl 2.3 L GAS
- B2500 | 1998-2000 | SE, SX, Troy Lee | 4 Cyl 2.5 L GAS
- B3000 | 1998-2007 | Base, DS, SE, SX, Troy Lee | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
- B4000 | 2001-2007, 1999 | Base, DS, SE | 6 Cyl 4.0 L GAS
View More
View related parts
Mazda Drive Shaft Part Number: 1F71-25-100A
$131.97 MSRP: $173.22
You Save: $41.25 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller; Drive Shaft Assembly
Fits the following Mazda Models:
- B2300 | 2001-2008 | Base, SE, SX | 4 Cyl 2.3 L GAS
- B2500 | 1998-2001 | SE, SX, Troy Lee | 4 Cyl 2.5 L GAS
- B3000 | 1998-2007 | Base, DS, SE, SX, Troy Lee | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
- B4000 | 1998-2007 | Base, DS, SE | 6 Cyl 4.0 L GAS
View More
View related parts
Mazda Drive Shaft Part Number: PF38-25-100
$620.61 MSRP: $848.01
You Save: $227.40 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Propeller-Front
Fits the following Mazda Models:
- Miata | 2004-2005 | Mazdaspeed | 4 Cyl 1.8 L GAS

| Page 1 of 4 |Next >

1-20 of 63 Results

Mazda Drive Shaft

Mazda Drive Shaft is an efficient way of transferring power from the engine to the wheels to support the responsive handling drivers expect. Mazda has its roots in 1931 and gained fame with the legendary rotary engine. Today, Mazda is pushing the envelope with SKYACTIV technology that reduces weight and improves fuel efficiency without reducing performance. The KODO Soul of Motion design wraps each body in sleek curves that suggest movement even when parked, while i-ACTIVSENSE safety features like radar cruise and lane-keep watch for dangers on the road while drivers are free to enjoy the fun. Rigorous testing on rough terrain shapes the i-ACTIV AWD system, and fresh ventures into electric drive and mild hybrids prove Mazda is still future ready. The Drive Shaft that spans every rear-wheel drive platform in the lineup plays the role of the mechanical bridge between transmission and differential and is constructed with a high strength to low weight ratio that avoids the introduction of extra inertia and keeps acceleration lively. Universal joints at both ends let it rotate easily as suspension angles vary, and a splined slip section lets the assembly stretch or contract with every bump, protecting against binding. Each Mazda Drive Shaft is resistant to twisting forces from hard launches or quick stops, reducing vibration and thus power arrives steady and occupants enjoy the signature feel.

You'll get great performance and real durability when you pick genuine OEM Drive Shaft. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Drive Shaft Parts and Q&A

Drive Shaft
P086-25-100
Q:
How to remove and install the rear Drive Shaft on Mazda B2200?
A:
Installation of the driveshaft and the removal of the same in the Navajo model requires that the negative battery cable is disconnected and the vehicle is raised safely. Mark the driveshaft yoke against the axle flange and then unhook it, after which the driveshaft needs to be disconnected to the axle companion flange and the back end of the transfer case and then the driveshaft itself should be removed. To install, fit driveshaft with the slip yoke facing the front, insert the bolts and loosen them to 41-55 ft. lbs. make sure the index mark on rear yoke coincides with the index mark on axle companion flange. In Pickup and MPV models, matchmark the rear U-joint and the rear companion flange, unbolt the U-joint, and dismount the center support bearing bracket and withdraws the driveshaft out of the transmission and stuffs the rear seal opening. Installation is the opposite of removal and match marks are to be aligned and the rear companion flange bolts tightened to 39-47 ft. lbs and the center bearing bracket nuts tightened to 27-38 ft. lbs. In the case of U- joint replacement, the operations performed are similar to the one-cardan U-joint. To solve the issue of driveshaft balancing, vibrations can be used to show an indication of an imbalance and this imbalance can be due to faulty universal joints or the wrong angle that is used, not necessarily the driveshaft itself. Check, check, Clean, Check: To check, raise the vehicle, check the propeller shaft, check the universal joints and clamp bolts, and check universal joints and clamp bolts. Trace the shaft and drive the vehicle to determine the intensity and speed of vibration and may use screw clamps to reduce the vibration. In case there are unacceptable vibration, repeat the procedure on the front part of the propeller shaft. To check the run-out, clean up surface of the shaft, screw a dial indicator perpendicular to the shaft and check at given points and change the propeller shaft when the measurements are more than 0.035 inch in the case of Navajo models and 0.016 inch in the case of Pickup and MPV models.
Drive Shaft
P058-25-010B
Q:
How to remove and install the drive shaft and universal joint on Mazda 929?
A:
To install and uninstall the rear driveshaft on different models, you will have to start by lifting the rear end of the car safely placing it on jackstands. Mark the drive shaft and pinion flanges so that they fit during reassembly. It can be done by loosening the bolts between the driveshaft and the pinion flange and in the case of the 929 model, the center bearing support bracket is unbolted and then the lower part of the driveshaft is lowered and the front part of the driveshaft can be slid out of the transmission. To ensure that there is no leakage of fluid, seal the transmission hole with an appropriate technique. To install it, insert the front part of the drive shaft into the transmission, lift the rear part onto the pinion flange, and make sure that the matchmarks align properly then tighten the flange bolts up to definite values. In the case of RX-7, the driveshaft should be installed at the same location as indicated not to cause vibrations and the tightening of the bolts must be done as indicated by the model. In performing the overhaul of the joint, matchmark the yoke and driveshaft, remove the bearing snaprings and drive out the bearing cups with great care. Check the wear of the spider, measure its diameter and change when needed. Installation Prepare the bearers by stuffing the bearing cups with grease, attaching the rollers and dust seals, and making sure that the U-joint has slight drag and is not binding. Lastly, test the U-joint assembly to operations.