How to remove and install the differential on Mazda MX-5 Miata?

Unscrew the lug nuts at the back, lift up the car and then place it in jackstands and then take off the rear wheels. Take out the exhaust system and hold the transmission in place, then take out the power plant frame, being careful not to drop down the cables and electrical wire connecting to the transmission. Disassemble the driveshaft, and on cars with ABS, also remove both rear wheel ABS sensors and harnesses off the rear knuckles, and put them in a safe place. In the case of 1997 and older models, unplug the speedometer cable. In 1996 models and earlier models, loosen the nuts that attach the inner CV joints to the differential output shaft flanges, and unscrew the upper control arm-to-rear knuckle pivot bolt to allow. In 1996 models and earlier remove the nuts that hold the inner CV joints to the differential output shaft flanges, and unscrew the upper control arm-to-rear knuckle pivot bolt to provide room to separate the inner CV joints, supporting the driveaxles with wire so that they do not hang against the On 1997 to 2005 models with splined inner CV joints that directly lead to the differential, totally eliminate the driveaxles. With them fitted, take out the tubes that hold the differential mount upon, with the support of a jack on the differential, and take out the mounting nuts on the upper mount on each side of the differential. Displace the differential forwards, downwards, and smooth it off. To remove the driveaxles of 2006 and subsequent models, find two bolts that hold the differential mount to the brackets on the back suspension cross member with a flashlight, then drop and remove the differential and the differential mount as one piece. Disassemble the four nuts that mounted the differential mount to the differential, and remove the differential mount. Installation is the opposite procedure as removal, making all the fasteners tighter, and verify that the level of the differentials is sufficient, topping it up, should the need arise.

How to remove and install the differential on Mazda Tribute?

To raise the rear of the vehicle and ensure that it is on jackstands without rolling the front wheels, start with 2004 and older models but first start with jackstands and ensure that the rear side is raised. It is then removed by removing the driveshaft and driveaxles, then the bolt holding the differential bracket to the subframe and then the three bolts holding the differential mass damper. Unscrew the electrical connector at the tip of the top of the differential, use a floor jack to stabilize the rear, and remove four bolts holding the differential on the brackets. Unscrew the bolts which hold the brackets to the subframe, lift the brackets and take the differential out. Installation: When installing install all mass damper bolts finger tight, and then tighten them in the required sequence, all the fasteners should be tightened to the required specification. On models 2005-2012, lift the vehicle up and place it on jackstands and take out the spare tire, rear driveaxles and then the driveshaft. Install a floor jack underneath the differential, tie-downs, and disconnect the wiring, and then take away the differential front mounting brackets. Ensure that the differential is stabilized on an assistant and remove the three mount bolts at the rear and then with caution, lower and remove a differential, tightening the fasteners to the recommended torque when installing. To model years 2013 and subsequent, jack and place the vehicle on jackstands, loosen the driveaxles and vehicle rear subframe including the differential attached. Unscrew the four mounting bolts of the front and two of the rear of the differential assembly, then the three of the left and right mounting bracket bolts, lastly, unscrew the differential off the subframe. When installing, make sure that all fasteners are tightened to the recommended torque.

Genuine Mazda Differential

Front Differential

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

85 Differentials found

View related parts
Mazda Carrier Assembly Part Number: KAT2-27-020
$2585.24 MSRP: $3532.45
You Save: $947.21 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
- Replaces: KA03-27-020
Fits the following Mazda Models:
- CX-5 | 2017-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
- CX-9 | 2018-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda Carrier Part Number: MA55-27-100J
$1609.24 MSRP: $2198.85
You Save: $589.61 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
- Replaces: MA55-27-100H
Fits the following Mazda Models:
- MX-5 Miata | 2016-2018 | Club, Grand Touring, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Differential Assembly Part Number: KA04-27-100F
$1064.61 MSRP: $1454.67
You Save: $390.06 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential
- Replaces: KA04-27-100D, KA04-27-100C, KA04-27-100E
Fits the following Mazda Models:
- CX-50 | 2023-2025 | 2.5 S, 2.5 Turbo, Hybrid Preferred, Hybrid Premium | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
View related parts
Mazda Housing Part Number: MA02-27-600A
$1107.83 MSRP: $1513.73
You Save: $405.90 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Casing, Differential; Carrier Cover, Differential Carrier
Fits the following Mazda Models:
- Miata | 1999-2005, 1994-1997 | 10th Anniversary, Base, LS, M Edition, Mazdaspeed, SE, STO, Shinsen | 4 Cyl 1.8 L GAS
View related parts
Mazda Carrier Part Number: MA57-27-100A
$1421.61 MSRP: $1942.46
You Save: $520.85 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
Fits the following Mazda Models:
- MX-5 Miata | 2019-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF GT, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Carrier Part Number: MA53-27-100C
$1533.75 MSRP: $2095.70
You Save: $561.95 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
- Replaces: MA53-27-100B, MA53-27-100A
Fits the following Mazda Models:
- MX-5 Miata | 2016-2018 | Club, Grand Touring, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Carrier Part Number: MS17-27-100A
$1540.25 MSRP: $2104.58
You Save: $564.33 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
Fits the following Mazda Models:
- MX-5 Miata | 2019-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF GT, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Carrier Part Number: MA33-27-100E
$1606.89 MSRP: $2195.64
You Save: $588.75 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
- Replaces: MA33-27-100D, MA33-27-100
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, SV, Special Edition, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Differential Part Number: CAT3-27-020B
$1762.23 MSRP: $2407.90
You Save: $645.67 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Carrier, Carrier Assembly, Differential Assembly
- Replaces: CA03-27-020B, CA02-27-020D, CAT3-27-020, CAT2-27-020C, CA02-27-020C, CAT2-27-020B, CD02-27-020, CA03-27-020, CAT3-27-020A, CA02-27-020B
Fits the following Mazda Models:
- 3 | 2019-2025 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
- CX-30 | 2020-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Driving & Differential Part Number: KAT1-27-020B
$3661.10 MSRP: $5002.49
You Save: $1341.39 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: DRIVING & DIFF.; Carrier Assembly, Differential Assembly
- Replaces: KA01-27-020A, KA01-27-020, KAT1-27-020A
Fits the following Mazda Models:
- CX-5 | 2013-2016 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
- CX-9 | 2016-2017 | Grand Touring, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda Carrier Part Number: RS06-27-100G
$609.85 MSRP: $4007.67
You Save: $3397.82 (85%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
- Replaces: RS06-27-100C, RS06-27-100, RS06-27-100E, RS06-27-100F
Fits the following Mazda Models:
- RX-8 | 2009-2011 | Grand Touring, R3, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Carrier Part Number: MA27-27-150A
$429.97 MSRP: $578.03
You Save: $148.06 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Carrier, Differential; Axle Housing, Differential Carrier
- Replaces: MA27-27-150
Fits the following Mazda Models:
- 6 | 2006-2007 | Mazdaspeed, S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
- CX-7 | 2007-2012 | Grand Touring, SV, Sport, Touring | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
- CX-9 | 2007-2015 | Grand Touring, Sport, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View More
View related parts
Mazda Carrier Part Number: RA13-27-100M
$2233.95 MSRP: $3052.46
You Save: $818.51 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
- Replaces: RA13-27-100K, RA13-27-100E, RA13-27-100L
Fits the following Mazda Models:
- RX-8 | 2004-2011 | 40th Anniversary Edition, Base, Grand Touring, R3, Shinka, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Housing Part Number: RA12-27-150B
$658.23 MSRP: $899.40
You Save: $241.17 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Carrier, Differential; Differential Carrier
Fits the following Mazda Models:
- RX-8 | 2004-2005 | Base, Shinka | 2 Cyl 1.3 L GAS
View related parts
Mazda Housing Part Number: T020-27-600G
$788.19 MSRP: $1076.99
You Save: $288.80 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Casing, Differential; Differential Carrier
Fits the following Mazda Models:
- Miata | 1990-1993 | Base, LE, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda Driving & Differential Part Number: TAA4-27-100J
$1339.77 MSRP: $1830.66
You Save: $490.89 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: DRIVING & DIFF.; Carrier, Carrier Assembly
- Replaces: TAA4-27-100F, TAA4-27-100G, TAA4-27-100E, TAA4-27-100H
Fits the following Mazda Models:
- CX-70 | 2025 | PHEV, Turbo, Turbo S | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
- CX-90 | 2024-2025 | PHEV, Turbo, Turbo S | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
View related parts
Mazda Driving & Differential Part Number: RA36-27-100D
$1415.22 MSRP: $1933.75
You Save: $518.53 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: DRIVING & DIFF.; Carrier, Differential Assembly
- Replaces: RA36-27-100B
Fits the following Mazda Models:
- CX-70 | 2025 | Turbo, Turbo S | 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
- CX-90 | 2024-2025 | Turbo, Turbo S | 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
View related parts
Mazda Driving & Differential Part Number: RA39-27-100D
$1527.32 MSRP: $2086.92
You Save: $559.60 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: DRIVING & DIFF.; Carrier, Differential Assembly
- Replaces: RA39-27-100B
Fits the following Mazda Models:
- CX-70 | 2025 | PHEV | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
- CX-90 | 2024-2025 | PHEV | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Mazda Carrier Part Number: MA56-27-100A
$1539.85 MSRP: $2104.03
You Save: $564.18 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
Fits the following Mazda Models:
- MX-5 Miata | 2019-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF GT, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Carrier Part Number: MA29-27-100E
$1578.57 MSRP: $2156.95
You Save: $578.38 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Driving & Differential; Differential Assembly
- Replaces: MA29-27-100A, MA29-27-100D
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, SV, Special Edition, Sport, Touring | 4 Cyl 2.0 L GAS

| Page 1 of 5 |Next >

1-20 of 85 Results

Mazda Differential

The Mazda Differential allows power to shift easily from wheel to wheel, providing every Mazda car with confident traction in everyday driving as well as spirited cornering. Mazda has a history dating back to 1931, is a champion of rotary engine ingenuity and now is moving forward with Skyactiv powertrains that stretch fuel while keeping throttle response spry. Its Kodo Soul of Motion styling combines sleek lines and inviting cabins, and i-Activsense features such as lane-keep and radar cruise help drivers stay alert and secure. Mazda also examines options for electric drive and mild hybrids so owners have greener options without missing the fun-to-drive nature of the brand, while i-Activ AWD proves itself on rough roads. At the heart of that confident ride, the Mazda Differential divides the torque coming from the engine to have left and right wheels turning at different speeds when the car goes around a corner, preventing the tires from scrubbing and allowing for tight, smooth arcs. Front-drive layouts contain an open Differential that balances power but allows the wheels to turn freely, while all-wheel drive versions add a rear unit and a center coupling that allows front and rear axles to adjust to varying grip. For drivers who are seeking additional bite in mud or snow, a limited-slip type can provide more torque to the tire with traction at the cost of a little weight for stronger launches and reduced wheelspin. Fresh lubricant makes the Differential quiet and durable while taking you on every journey in a precise and stable way.

You'll get great performance and real durability when you pick genuine OEM Differential. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Differential Parts and Q&A

Carrier
MA29-27-100E
Q:
How to remove and install the differential on Mazda MX-5 Miata?
A:
Unscrew the lug nuts at the back, lift up the car and then place it in jackstands and then take off the rear wheels. Take out the exhaust system and hold the transmission in place, then take out the power plant frame, being careful not to drop down the cables and electrical wire connecting to the transmission. Disassemble the driveshaft, and on cars with ABS, also remove both rear wheel ABS sensors and harnesses off the rear knuckles, and put them in a safe place. In the case of 1997 and older models, unplug the speedometer cable. In 1996 models and earlier models, loosen the nuts that attach the inner CV joints to the differential output shaft flanges, and unscrew the upper control arm-to-rear knuckle pivot bolt to allow. In 1996 models and earlier remove the nuts that hold the inner CV joints to the differential output shaft flanges, and unscrew the upper control arm-to-rear knuckle pivot bolt to provide room to separate the inner CV joints, supporting the driveaxles with wire so that they do not hang against the On 1997 to 2005 models with splined inner CV joints that directly lead to the differential, totally eliminate the driveaxles. With them fitted, take out the tubes that hold the differential mount upon, with the support of a jack on the differential, and take out the mounting nuts on the upper mount on each side of the differential. Displace the differential forwards, downwards, and smooth it off. To remove the driveaxles of 2006 and subsequent models, find two bolts that hold the differential mount to the brackets on the back suspension cross member with a flashlight, then drop and remove the differential and the differential mount as one piece. Disassemble the four nuts that mounted the differential mount to the differential, and remove the differential mount. Installation is the opposite procedure as removal, making all the fasteners tighter, and verify that the level of the differentials is sufficient, topping it up, should the need arise.
Carrier
ZZCB-27-100B
Q:
How to remove and install the differential on Mazda Tribute?
A:
To raise the rear of the vehicle and ensure that it is on jackstands without rolling the front wheels, start with 2004 and older models but first start with jackstands and ensure that the rear side is raised. It is then removed by removing the driveshaft and driveaxles, then the bolt holding the differential bracket to the subframe and then the three bolts holding the differential mass damper. Unscrew the electrical connector at the tip of the top of the differential, use a floor jack to stabilize the rear, and remove four bolts holding the differential on the brackets. Unscrew the bolts which hold the brackets to the subframe, lift the brackets and take the differential out. Installation: When installing install all mass damper bolts finger tight, and then tighten them in the required sequence, all the fasteners should be tightened to the required specification. On models 2005-2012, lift the vehicle up and place it on jackstands and take out the spare tire, rear driveaxles and then the driveshaft. Install a floor jack underneath the differential, tie-downs, and disconnect the wiring, and then take away the differential front mounting brackets. Ensure that the differential is stabilized on an assistant and remove the three mount bolts at the rear and then with caution, lower and remove a differential, tightening the fasteners to the recommended torque when installing. To model years 2013 and subsequent, jack and place the vehicle on jackstands, loosen the driveaxles and vehicle rear subframe including the differential attached. Unscrew the four mounting bolts of the front and two of the rear of the differential assembly, then the three of the left and right mounting bracket bolts, lastly, unscrew the differential off the subframe. When installing, make sure that all fasteners are tightened to the recommended torque.