How to remove and install the Evaporator in an air conditioning system on Mazda MPV?

One must empty the cooling system by first pumping the air conditioning, and pulling out the negative cable attached to the battery when removing the front evaporator. The second step is to remove the passenger side lower glovebox and trim to reveal the cooling unit case. Find and remove the refrigerant lines at the firewall location, then use a backup wrench to help avoid twisting of the tubing, and seal all the refrigerant lines to seal out moisture. To install the evaporator case, which is located on the passenger side of the firewall, remove the grommets, disconnect the electrical connector on the thermo switch and remove the attaching nuts. Remove the screws that hold the upper and lower halves of the evaporator and remove the evaporator. To install, turn the process of removal in reverse and make sure to fill the cooling system up, then evacuate, recharge, and leak test the air conditioning system with a qualified shop. In the case of the rear evaporator, release air conditioning system, and unhook the negative cable with battery. Take out the trim panel on the left rear side, switch the refrigerant lines off the evaporator and then take out all the electrical connections and hoses to the cooling unit assembly. Dismantle by un-bolstering the evaporator by detaching the rear cooling unit nuts and bolts and then detach the upper and lower half of the case to gain access to the evaporator and remove it. Installation is the opposite of the removal process and the same will be necessary in evacuation, recharging and leak testing of air conditioning system.

How to properly remove and replace the Evaporator and A/C Expansion Valve in an air conditioning system on Mazda Protege?

Start with the release and recovery of the refrigerant by a qualified repair facility. Disconnect the air conditioning lines at the firewall (with a backup wrench to avoid damaging the fittings) and cap the open fittings with a cap after dismantling to avoid air or dirt getting inside. Take out the glove box cover, side panel, and under dash panel on the passenger side. In the case of models between 1995 and 1998, delete the cooling unit duct and the wire connecting the blower unit and the air intake. Remove the electrical connector(s) of the A/C Evaporator Core and Unlock the seal plates on each side of the A/C Evaporator Core. Loosen the mounting studs of the firewall with the nuts of the A/C Evaporator Core and then attach the A/C Evaporator Core. Disassemble the lower and upper cooling unit housings by taking out the clips of the cooling unit housing, then take out the A/C Evaporator Core. Unattachment of expansion valve fittings and taking out the expansion valve out of the A/C Evaporator Core is required, and the fittings of the expansion valve must be capped immediately to prevent the expansion valve from being exposed to moisture and contamination. To do this, where required, on models with air conditioning from 1990 to 1994, take out the air conditioning thermoswitch in the upper cooling unit housing; on models with air conditioning from 1995 or later, take out the thermoswitch in the A/C Evaporator Core and fit it in the same position. Inspect the A/C Evaporator Core and fittings by checking for cracking or damage, replacing the A/C Evaporator Core as required. Recover the expansion valve, with the gaskets and tightening the inlet and outlet fittings. Removal is the converse of the system installation, where it is always ensured to remove any O-rings and replace them with new ones depending on the type of refrigerant in your system, and lubricate them with refrigerant oil before fitting. Lastly, make sure the system gets emptied, refilled, and sealed by the shop it was emptied by, and in case of a new A/C Evaporator Core, add new refrigerant oil to the high-pressure side of the compressor, but only with oil that is compatible with your system.

Genuine Mazda Evaporator

A/C Evaporator Core

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

54 Evaporators found

View related parts
Mazda Evaporator Core Part Number: BDGF-61-J10
$468.16 MSRP: $629.37
You Save: $161.21 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator
Fits the following Mazda Models:
- 3 | 2019-2025 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Evaporator Part Number: GHP9-61-J10A
$549.59 MSRP: $738.84
You Save: $189.25 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator Core
- Replaces: BPP3-61-J10, BJS7-61-J10, BJS7-61-J10A
Fits the following Mazda Models:
- 3 | 2014-2018 | Grand Touring, I Sport, I Touring, Sport, Touring, i Grand Touring, i SV, s Grand Touring, s Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
- 6 | 2016-2021 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
- CX-5 | 2016-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View More
View related parts
Mazda Evaporator Core Part Number: TKY0-61-J1Z
$697.24 MSRP: $952.71
You Save: $255.47 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator
Fits the following Mazda Models:
- CX-9 | 2021-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda Evaporator Core Part Number: TKY8-61-J1Z
$730.37 MSRP: $997.97
You Save: $267.60 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator, Cooling Unit-Rear
Fits the following Mazda Models:
- CX-9 | 2021-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda Evaporator Assembly Part Number: NA1P-61-130A
$1255.55 MSRP: $1715.57
You Save: $460.02 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Heater Unit; Case Assembly
- Replaces: NA1P-61-130
Fits the following Mazda Models:
- MX-5 Miata | 2016-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Evaporator Assembly Part Number: NE51-61-130G
$1835.65 MSRP: $2508.22
You Save: $672.57 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Heater Unit
- Replaces: NE51-61-130E
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, SV, Special Edition, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Evaporator Part Number: BDTS-61-J10
$202.84 MSRP: $270.50
You Save: $67.66 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator Core
Fits the following Mazda Models:
- 3 | 2019-2025 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
- CX-30 | 2020-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Evaporator Part Number: DD2F-61-J10A
$511.29 MSRP: $687.36
You Save: $176.07 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator Core
- Replaces: DD2F-61-J10
Fits the following Mazda Models:
- CX-3 | 2016-2021 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Evaporator Part Number: NA1P-61-J10
$347.16 MSRP: $462.98
You Save: $115.82 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator Core
Fits the following Mazda Models:
- MX-5 Miata | 2016-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Evaporator Core Part Number: L206-61-J10A
$622.99 MSRP: $851.25
You Save: $228.26 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator
- Replaces: L206-61-J10
Fits the following Mazda Models:
- CX-9 | 2007-2015 | Grand Touring, Sport, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda Evaporator Assembly Part Number: BJ0M-61-520
$639.29 MSRP: $873.52
You Save: $234.23 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Unit, Cooling
Fits the following Mazda Models:
- Protege | 2001-2003 | DX, ES, LX, MP3, Mazdaspeed | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS
- Protege5 | 2002-2003 | Base | 4 Cyl 2.0 L GAS
View related parts
Mazda Evaporator Core Part Number: TK48-61-P10A
$676.40 MSRP: $924.23
You Save: $247.83 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator, Cooling Unit-Rear
- Replaces: TK48-61-P10
Fits the following Mazda Models:
- CX-9 | 2016-2020 | Grand Touring, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda Evaporator Part Number: TD11-61-P10A
$814.53 MSRP: $1112.97
You Save: $298.44 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator, Cooling Unit-Rear; Evaporator Core
- Replaces: TD11-61-P10
Fits the following Mazda Models:
- CX-9 | 2007-2015 | Grand Touring, Sport, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda Core Part Number: TA01-61-J10B
$835.97 MSRP: $1142.26
You Save: $306.29 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator; Evaporator Core
Fits the following Mazda Models:
- Millenia | 1995-2002 | Base, L, Millennium Edition, S | 6 Cyl 2.3 L GAS, 6 Cyl 2.5 L GAS
View related parts
Mazda Evaporator Part Number: FE03-61-J10A
$860.36 MSRP: $1175.58
You Save: $315.22 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator Core
- Replaces: FE01-61-J10A, FE01-61-J10, FE02-61-J10A
Fits the following Mazda Models:
- RX-8 | 2004-2011 | 40th Anniversary Edition, Base, Grand Touring, R3, Shinka, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Evaporator Assembly Part Number: NC72-61-520D
$1351.89 MSRP: $1847.23
You Save: $495.34 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Unit, Cooling
- Replaces: NC72-61-520C
Fits the following Mazda Models:
- Miata | 2001 | Base, LS, SE | 4 Cyl 1.8 L GAS
View related parts
Mazda Evaporator Assembly Part Number: NE55-61-130B
$1516.95 MSRP: $2072.75
You Save: $555.80 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Heater Unit
- Replaces: NE55-61-130
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, SV, Special Edition, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Evaporator Part Number: VA54-61-J10
$114.69 MSRP: $152.95
You Save: $38.26 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator Core
Fits the following Mazda Models:
- CX-50 | 2023-2025 | 2.5 S, 2.5 Turbo, Hybrid Preferred, Hybrid Premium | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
View related parts
Mazda Evaporator Part Number: BBM4-61-J10
$347.51 MSRP: $463.45
You Save: $115.94 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator Core
Fits the following Mazda Models:
- 3 | 2010-2012 | Mazdaspeed, S, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Evaporator Part Number: KR9P-61-J10
$360.09 MSRP: $480.22
You Save: $120.13 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Evaporator Core
Fits the following Mazda Models:
- CX-70 | 2025 | PHEV, Turbo, Turbo S | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
- CX-90 | 2024-2025 | PHEV, Turbo, Turbo S | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)

| Page 1 of 3 |Next >

1-20 of 54 Results

Mazda Evaporator

Mazda Evaporator ensures that the air in the passenger cabin is cool and dry by pulling heat and moisture from the air. It makes every Mazda a fresh, comfortable, and fun vehicle to ride in. Mazda cars are lively to drive and stand out with KODO design and the engine range that combines strong power with low fuel use. Adding confidence is the i-ACTIVSENSE safety technology while the brand's commitment to electric drive shows it cares. Mazda cars understand that driving is fun. Therefore, Mazda makes cars in such a way that driving them remains fun in every weather. For this purpose, the company uses dynamic steering to achieve fun driving. The cars are also made quiet so customers never feel tired even after long trips. Furthermore, optional i-ACTIV all-wheel drive proves useful on slippery roads. As a result, this lets the lineup perform in many climates. The spirit of intelligent engineering makes possible the dependable climate system that lies concealed behind the dash. In the Evaporator component of the system, the liquid refrigerant lying inside aluminum tubes is transformed into a vapor. This is done with the help of warm interior air flowing past the finned tubes, which absorbs energy from the stream so that cool dry air returns to the passengers. The vehicle's fins also gather water, which drains outside the automobile and thus reduces humidity that could fog the windshields. The component is protected from debris by a sealed enclosure, while continuous airflow and clear drainage paths help keep it leak-free and working at optimum efficiency for years to come throughout temperature fluctuations. Because it absorbs both heat and moisture, the Mazda Evaporator is an important part of the air conditioning system and maintains comfort in every model the brand builds.

You'll get great performance and real durability when you pick genuine OEM Evaporator. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Evaporator Parts and Q&A

Evaporator Assembly
LB83-61-870B
Q:
How to remove and install the Evaporator in an air conditioning system on Mazda MPV?
A:
One must empty the cooling system by first pumping the air conditioning, and pulling out the negative cable attached to the battery when removing the front evaporator. The second step is to remove the passenger side lower glovebox and trim to reveal the cooling unit case. Find and remove the refrigerant lines at the firewall location, then use a backup wrench to help avoid twisting of the tubing, and seal all the refrigerant lines to seal out moisture. To install the evaporator case, which is located on the passenger side of the firewall, remove the grommets, disconnect the electrical connector on the thermo switch and remove the attaching nuts. Remove the screws that hold the upper and lower halves of the evaporator and remove the evaporator. To install, turn the process of removal in reverse and make sure to fill the cooling system up, then evacuate, recharge, and leak test the air conditioning system with a qualified shop. In the case of the rear evaporator, release air conditioning system, and unhook the negative cable with battery. Take out the trim panel on the left rear side, switch the refrigerant lines off the evaporator and then take out all the electrical connections and hoses to the cooling unit assembly. Dismantle by un-bolstering the evaporator by detaching the rear cooling unit nuts and bolts and then detach the upper and lower half of the case to gain access to the evaporator and remove it. Installation is the opposite of the removal process and the same will be necessary in evacuation, recharging and leak testing of air conditioning system.
Evaporator Assembly
BJ0M-61-520
Q:
How to properly remove and replace the Evaporator and A/C Expansion Valve in an air conditioning system on Mazda Protege?
A:
Start with the release and recovery of the refrigerant by a qualified repair facility. Disconnect the air conditioning lines at the firewall (with a backup wrench to avoid damaging the fittings) and cap the open fittings with a cap after dismantling to avoid air or dirt getting inside. Take out the glove box cover, side panel, and under dash panel on the passenger side. In the case of models between 1995 and 1998, delete the cooling unit duct and the wire connecting the blower unit and the air intake. Remove the electrical connector(s) of the A/C Evaporator Core and Unlock the seal plates on each side of the A/C Evaporator Core. Loosen the mounting studs of the firewall with the nuts of the A/C Evaporator Core and then attach the A/C Evaporator Core. Disassemble the lower and upper cooling unit housings by taking out the clips of the cooling unit housing, then take out the A/C Evaporator Core. Unattachment of expansion valve fittings and taking out the expansion valve out of the A/C Evaporator Core is required, and the fittings of the expansion valve must be capped immediately to prevent the expansion valve from being exposed to moisture and contamination. To do this, where required, on models with air conditioning from 1990 to 1994, take out the air conditioning thermoswitch in the upper cooling unit housing; on models with air conditioning from 1995 or later, take out the thermoswitch in the A/C Evaporator Core and fit it in the same position. Inspect the A/C Evaporator Core and fittings by checking for cracking or damage, replacing the A/C Evaporator Core as required. Recover the expansion valve, with the gaskets and tightening the inlet and outlet fittings. Removal is the converse of the system installation, where it is always ensured to remove any O-rings and replace them with new ones depending on the type of refrigerant in your system, and lubricate them with refrigerant oil before fitting. Lastly, make sure the system gets emptied, refilled, and sealed by the shop it was emptied by, and in case of a new A/C Evaporator Core, add new refrigerant oil to the high-pressure side of the compressor, but only with oil that is compatible with your system.