How to remove the front and rear bumper cover on Mazda Tribute?

Unplug the cable in the negative battery post and engage the parking brake lifting the car and holding it firmly on jackstands. On 2007 and older models, take out the pin retainers of the inner fender splash shield, take away the splash shield out of the front bumper area, and remove the front bumper cover pushpin type retainers. Detach the connector of the fog lamp (when fitted), the lower bolts of the bumper cover and the pin-shaped retainers on the front of the bumper cover. Once the two upper bumper cover mounting bolts have been removed, remove the front bumper mounting nuts and pull the bumper out of the car. In the case of the rear bumper cover, the pin retainers of the inner fender splash shield should be removed and pushed completely away and the screws of the rear bumper cover mounting removed out of the quarter panel. Take off the pin-type retainers below and the rear bumper cover mounting bolts then remove the rear bumper mounting nuts and the rear bumper. On 2008 and 2012 models, loosen the screws on the front bumper with removing the front wheels, then loosen the pushpins and bolts holding the front bumper cover. Disassemble the wiring of the parking sensor and fog lamps, unscrew the four buttons at the upper corners of the grille, unscrew the bumper by the fenders, and then proceed to remove the bumper cover with a lot of care. In the case of the rear bumper cover, ensure that you remove the rear wheels in case of need, remove the screws on the central part of the car, and remove the splash shields before removing the bumper cover. In 2013 and subsequent models, detach the front wheels, engine front under cover, fenderwell splash shields and outer trim. Close the front bumper covering lower retaining bolts, disconnect electrical connector and remove the upper cover straps. Before removing the bumper cover, ensure that you pull the bumper cover ends without the fenders and the headlight housing clips. STEP 20 relating to the front bumper, once the cover has been removed, unscrew any wiring dendrites, remove the bumper-to-subframe bolts and the bumper lower mounting nuts and then take off the front bumper. To install the rear bumper, lift up and hold the rear of the car, and unscrew the taillight casings so you can access concealed bolts, then remove the fenderwell splash plate and molding. Unscrew the bumper electrical connector at the back, loosen the screws holding the bumper on the car at the bottom and loosen the rear bumper off the car. In models with a trailer tow package, remove the retaining bolts on either side of the bumper, disconnect the electrical connector (where present) and slide the bumper/hitch out to remove it.

Genuine Mazda Tribute Bumper Cover

Bumper Shell

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Bumper Covers found

View related parts
Mazda Tribute Bumper Cover Part Number: ECY1-50-031K-BB
$653.48 MSRP: $892.92
You Save: $239.44 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Front
- Replaces: ECY1-50-031E, ECY1-50-031G, ECY1-50-031K, ECY1-50-031J, ECY1-50-031F, ECY1-50-031H
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Upper Cover Part Number: ZZC0-50-031-BB
$316.48 MSRP: $422.05
You Save: $105.57 (26%)
ADD TO CART
Product Specifications
- Other Name: Bumper, Front
- Position: Upper
- Replaces: ZZC0-50-031-AA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011 Mazda Tribute | Hybrid, S, i | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: EC04-50-221H-78
$338.44 MSRP: $451.34
You Save: $112.90 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Rear
- Replaces: EC01-50-221E-78, EC04-50-221F-78, ECTT-50-221G-78, EC01-50-221F-78, EC01-50-221G-78, EC01-50-221D-78, EC04-50-221D-78, EC04-50-221E-78, EC04-50-221G-78, EC01-50-221C-78, EC04-50-221C-78
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: EF96-50-031-44
$379.79 MSRP: $510.56
You Save: $130.77 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: BUMPER,FRONT ('01-'04MY)
- Replaces: EC01-50-031D-44, EC01-50-031E-44, EC02-50-031H-44, EC02-50-031D-44, EC02-50-031F-44, EC01-50-031F-44, EC01-50-031H-44, EC01-50-031G-44, ECTT-50-031H-44, EC02-50-031E-44, EC02-50-031G-44
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: EF91-50-031B-44
$430.91 MSRP: $579.30
You Save: $148.39 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Front
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mazda Tribute | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Lower Cover Part Number: ZZCB-50-221A
Product Specifications
- Other Name: BUMPER,REAR (LOWER)
- Position: Lower
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011 Mazda Tribute | Hybrid, S, i | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: ZZCA-50-221-BB
Product Specifications
- Other Name: Bumper, Rear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011 Mazda Tribute | Hybrid, S, i | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Lower Cover Part Number: ZZCA-50-031
Product Specifications
- Other Name: Bumper, Front
- Position: Lower
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011 Mazda Tribute | Hybrid, S, i | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: EF96-50-031-78
Product Specifications
- Other Name: BUMPER,FRONT ('01-'04MY)
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: EF95-50-221B-BB
Product Specifications
- Other Name: Bumper, Rear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mazda Tribute | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: EF95-50-031B-BB
Product Specifications
- Other Name: Bumper, Front
- Replaces: EF95-50-031-AA, EF95-50-031B-AA, ECTT-50-031-AA, EF95-50-031A-AA
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mazda Tribute | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: EF91-50-221A-44
Product Specifications
- Other Name: Bumper, Rear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mazda Tribute | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: ECY2-50-221-BB
Product Specifications
- Other Name: Bumper, Rear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Bumper Cover Part Number: EC04-50-221H-44
Product Specifications
- Other Name: Rear Bumper
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS

Mazda Tribute Bumper Cover

Mazda Tribute Bumper Cover is a soft outer panel that conceals the rigid bumper design and dresses the sport-utility body. The bumpers assist with steering air through the vehicle, which may improve speed and fuel economy. This Bumper Cover, located in the front or rear, is part of an assembly that may consist of grille inserts, light bezels, molding, and openings for fog lamps, parking lamps, turn signal, or tow eye hook. With the aid of smooth surfaces and smooth style, the cover directs the cooling air towards the radiator, oil coolers, power steering coolers, and even the brake via suitably shaped cavities and minimizes drag. The trim rings and decorative panels around this cavity improve styling and conceal exposed hardware. When no optional lights or towing hardware are fitted, matching caps or inserts snap into the unused openings to maintain a uniform exterior finish. Since the part deflects everyday scuff and damages the underlying energy-absorbing parts during minor impacts, the cracks, discoloration, or warpage from road debris, ultraviolet rays, or low-speed contact may require a Bumper Cover replacement. Every cover has been formed in such a way to fit on a specific attachment point on the Mazda platform so that it can hide the anchoring brackets but allow access when the tow eye hook is needed. When the component is properly installed, it ensures that the Mazda nameplate has the same styling and aerodynamics as well as impact protection as the Tribute line. There is consistency in the Mazda Tribute models.

Looking for Bumper Cover with proven quality? Choose OEM Bumper Cover. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda Tribute parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine Tribute part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda Tribute Bumper Cover Parts and Q&A

Bumper Cover
EC04-50-221H-44
Q:
How to remove the front and rear bumper cover on Mazda Tribute?
A:
Unplug the cable in the negative battery post and engage the parking brake lifting the car and holding it firmly on jackstands. On 2007 and older models, take out the pin retainers of the inner fender splash shield, take away the splash shield out of the front bumper area, and remove the front bumper cover pushpin type retainers. Detach the connector of the fog lamp (when fitted), the lower bolts of the bumper cover and the pin-shaped retainers on the front of the bumper cover. Once the two upper bumper cover mounting bolts have been removed, remove the front bumper mounting nuts and pull the bumper out of the car. In the case of the rear bumper cover, the pin retainers of the inner fender splash shield should be removed and pushed completely away and the screws of the rear bumper cover mounting removed out of the quarter panel. Take off the pin-type retainers below and the rear bumper cover mounting bolts then remove the rear bumper mounting nuts and the rear bumper. On 2008 and 2012 models, loosen the screws on the front bumper with removing the front wheels, then loosen the pushpins and bolts holding the front bumper cover. Disassemble the wiring of the parking sensor and fog lamps, unscrew the four buttons at the upper corners of the grille, unscrew the bumper by the fenders, and then proceed to remove the bumper cover with a lot of care. In the case of the rear bumper cover, ensure that you remove the rear wheels in case of need, remove the screws on the central part of the car, and remove the splash shields before removing the bumper cover. In 2013 and subsequent models, detach the front wheels, engine front under cover, fenderwell splash shields and outer trim. Close the front bumper covering lower retaining bolts, disconnect electrical connector and remove the upper cover straps. Before removing the bumper cover, ensure that you pull the bumper cover ends without the fenders and the headlight housing clips. STEP 20 relating to the front bumper, once the cover has been removed, unscrew any wiring dendrites, remove the bumper-to-subframe bolts and the bumper lower mounting nuts and then take off the front bumper. To install the rear bumper, lift up and hold the rear of the car, and unscrew the taillight casings so you can access concealed bolts, then remove the fenderwell splash plate and molding. Unscrew the bumper electrical connector at the back, loosen the screws holding the bumper on the car at the bottom and loosen the rear bumper off the car. In models with a trailer tow package, remove the retaining bolts on either side of the bumper, disconnect the electrical connector (where present) and slide the bumper/hitch out to remove it.