How to remove and install the Tailgate Handle and Trunk Lock Cylinder on Mazda 3?

For 2009 and earlier models, start by disconnecting the cable from the negative battery terminal, then open the liftgate and remove the trim panel. Through the large access hole, disengage the outside liftgate handle-to-latch rod and the outside liftgate lock-to-latch rod. All liftgate lock rods are attached by plastic clips, which can be removed by unsnapping the portion engaging the connecting rod and pulling the rod out of its locating hole. For models with power liftgate locks, disconnect the electrical connectors at the latch. Next, remove the screws securing the latch to the liftgate and take out the latch assembly through the liftgate opening, with installation being the reverse of removal. For 2010 and later models, remove the liftgate trim panels, disconnect the lock actuator electrical connector, and remove the mounting bolts and lock actuator assembly, again with installation being the reverse of removal. Regarding the liftgate lock cylinder and outside handle for 2009 and earlier models, open the liftgate and remove the trim panel, then disconnect the liftgate lock actuator connector and liftgate latch electrical connectors. Disconnect the lock clip and rod from the liftgate lock cylinder, remove the clips securing the cables, and detach the cable from the latch and lock actuator. Finally, remove the latch and lock assembly mounting bolts and take out the latch and lock, with installation being the reverse of removal. Note that there is no lock cylinder or exterior handle on 2010 and later models.

How to disconnect and remove the Trunk Lock Cylinder,Ignition Lock Cylinder and Trunk Lid Latch on Mazda 6?

Disconnect the cable from the negative battery terminal and remove the trunk lid trim panel. Rotate the trunk lid actuator rod mounting clip and disconnect the rod from the trunk lid key lock cylinder assembly, then disconnect the electrical connector from the lock cylinder if equipped. Remove the mounting nuts and maneuver the lock cylinder out from the trunk lid, with installation being the reverse of removal. Next, disconnect the actuator rod from the trunk lid lock cylinder and the electrical connector from the trunk lid latch. Remove the latch mounting bolts and take out the latch, with installation again being the reverse of removal.

Genuine Mazda Trunk Lock Cylinder

Back Door Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

40 Trunk Lock Cylinders found

View related parts
Mazda Lock Cylinder Part Number: GPYA-76-230
$105.65 MSRP: $140.90
You Save: $35.25 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
Fits the following Mazda Models:
- 6 | 2006-2007 | Mazdaspeed, S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: GKYA-76-230A
$68.59 MSRP: $91.48
You Save: $22.89 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
- Replaces: GKYA-76-230
Fits the following Mazda Models:
- 6 | 2003-2008 | Mazdaspeed, S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Cylinder & Keys Part Number: B2YH-76-260
$70.94 MSRP: $94.60
You Save: $23.66 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Lift Gate; Cylinder & Key
Fits the following Mazda Models:
- Protege5 | 2002-2003 | Base | 4 Cyl 2.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: B2YD-76-230A
$76.08 MSRP: $101.46
You Save: $25.38 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
Fits the following Mazda Models:
- Protege | 1999-2003 | DX, ES, LX, MP3, Mazdaspeed | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Protege5 | 2002-2003 | Base | 4 Cyl 2.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: NCY1-76-230A
$98.51 MSRP: $131.37
You Save: $32.86 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Set; Cylinder & Key
Fits the following Mazda Models:
- Miata | 1999-2003 | 10th Anniversary, Base, LS, SE, Shinsen | 4 Cyl 1.8 L GAS
View related parts
Mazda Lock Cylinder Part Number: GKYC-76-230B
$109.40 MSRP: $145.90
You Save: $36.50 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
- Replaces: GKYC-76-230A
Fits the following Mazda Models:
- 6 | 2003-2008 | Mazdaspeed, S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: ECY1-76-26YA
$111.15 MSRP: $148.22
You Save: $37.07 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Kit, Lift Gate; Key Cylinder
Fits the following Mazda Models:
- Tribute | 2001-2006 | DX, ES, LX, S, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: BP4K-62-498B
$6.94 MSRP: $9.25
You Save: $2.31 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Vessel, Lock Cylinder-T/Li
Fits the following Mazda Models:
- 3 | 2004-2013 | S, SP23, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: NEY1-76-230
$20.15 MSRP: $26.46
You Save: $6.31 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
Fits the following Mazda Models:
- Miata | 2004-2005 | Base, LS, Mazdaspeed | 4 Cyl 1.8 L GAS
View related parts
Mazda Lock Cylinder Part Number: TA01-76-230D
$22.11 MSRP: $29.02
You Save: $6.91 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
Fits the following Mazda Models:
- Millenia | 1995-2002 | Base, L, Millennium Edition, S | 6 Cyl 2.3 L GAS, 6 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: BR95-76-260A
$93.69 MSRP: $124.95
You Save: $31.26 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Set; Cylinder & Key
Fits the following Mazda Models:
- 323 | 1990-1994 | Base, SE | 4 Cyl 1.6 L GAS
View related parts
Mazda Lock Cylinder Part Number: GKYC-76-230
$101.33 MSRP: $135.13
You Save: $33.80 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk
Fits the following Mazda Models:
- 6 | 2003 | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: B21H-76-230C
$103.18 MSRP: $137.59
You Save: $34.41 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
Fits the following Mazda Models:
- Protege | 1996-1998 | DX, ES, LX | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Lock Cylinder Part Number: NEY5-76-230
$105.18 MSRP: $140.26
You Save: $35.08 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, SV, Special Edition, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: NA14-76-230F
$107.36 MSRP: $143.17
You Save: $35.81 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
Fits the following Mazda Models:
- Miata | 1990-1997 | Base, LE, M Edition, SE, STO | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Lock Cylinder Part Number: GA2K-76-230B
$107.48 MSRP: $143.32
You Save: $35.84 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk; Cylinder & Key
Fits the following Mazda Models:
- 626 | 1993-1997 | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Mazda Lock Cylinder Part Number: NEZ1-76-230
$115.16 MSRP: $153.57
You Save: $38.41 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, SV, Special Edition, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Lock Cylinder Part Number: FEY5-76-230
$123.26 MSRP: $164.39
You Save: $41.13 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk
Fits the following Mazda Models:
- RX-8 | 2004-2008 | 40th Anniversary Edition, Base, Grand Touring, Shinka, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Lock Cylinder Part Number: FFY4-76-230
$133.35 MSRP: $177.83
You Save: $44.48 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk
Fits the following Mazda Models:
- RX-8 | 2009-2011 | Grand Touring, R3, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Lock Cylinder Part Number: BNYP-76-230B
$134.21 MSRP: $178.99
You Save: $44.78 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Key Sub Set, Trunk
- Replaces: B3YD-76-230, B3YD-76-230B, B3YD-76-230A, BNYP-76-230A, BNYP-76-230
Fits the following Mazda Models:
- 3 | 2004-2012 | S, SP23, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS

| Page 1 of 2 |Next >

1-20 of 40 Results

Mazda Trunk Lock Cylinder

The Mazda Trunk Lock Cylinder is ideal for drivers that need easy key controlled protection. It keeps the trunk shut until the right key is turned, then releases. This makes loading and unloading fast and safe. Mazda's innovative ideas have given the brand an enviable reputation around the globe. From the early rotary engine which turned many racers into fans of the brand to the current day SKYACTIV technologies which help extract greater distances from every gallon of fuel. The KODO design language enables Mazda designers to shape each hood and fender with a sense of motion, even at rest. The i-ACTIVSENSE safety systems are always watching the road with smart sensors that help drivers keep pace, change lanes, and brake with confidence. In its cars, Mazda also plays with electric drives, mild hybrids, and i-ACTIV all-wheel drive. However, it shows that one can be efficient without taking the fun out of driving. In fact, the brand's cars feel nimble when taken down a winding road, yet relaxed when on the daily commute. In this range of forward-thinking technologies, the Trunk Lock Cylinder plays a basic yet critical role for security. The Trunk Lock Cylinder fits firmly into the trunk latch assembly to accept the matched key and to provide consistent engagement. So, valuable gear like backpacks, sports equipment, or emergency tools can be easily concealed when the car is left unattended. Due to the durable metal tumbler and precision key profile design, drivers achieve smooth operation with minimal turning effort. Furthermore, the cylinder also integrates across Mazda models allowing families, commuters, and enthusiasts to have confidence that their belongings are safe.

You'll get great performance and real durability when you pick genuine OEM Trunk Lock Cylinder. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Trunk Lock Cylinder Parts and Q&A

Lock Cylinder
BP4K-62-498B
Q:
How to remove and install the Tailgate Handle and Trunk Lock Cylinder on Mazda 3?
A:
For 2009 and earlier models, start by disconnecting the cable from the negative battery terminal, then open the liftgate and remove the trim panel. Through the large access hole, disengage the outside liftgate handle-to-latch rod and the outside liftgate lock-to-latch rod. All liftgate lock rods are attached by plastic clips, which can be removed by unsnapping the portion engaging the connecting rod and pulling the rod out of its locating hole. For models with power liftgate locks, disconnect the electrical connectors at the latch. Next, remove the screws securing the latch to the liftgate and take out the latch assembly through the liftgate opening, with installation being the reverse of removal. For 2010 and later models, remove the liftgate trim panels, disconnect the lock actuator electrical connector, and remove the mounting bolts and lock actuator assembly, again with installation being the reverse of removal. Regarding the liftgate lock cylinder and outside handle for 2009 and earlier models, open the liftgate and remove the trim panel, then disconnect the liftgate lock actuator connector and liftgate latch electrical connectors. Disconnect the lock clip and rod from the liftgate lock cylinder, remove the clips securing the cables, and detach the cable from the latch and lock actuator. Finally, remove the latch and lock assembly mounting bolts and take out the latch and lock, with installation being the reverse of removal. Note that there is no lock cylinder or exterior handle on 2010 and later models.
Lock Cylinder
GPYA-76-230
Q:
How to disconnect and remove the Trunk Lock Cylinder,Ignition Lock Cylinder and Trunk Lid Latch on Mazda 6?
A:
Disconnect the cable from the negative battery terminal and remove the trunk lid trim panel. Rotate the trunk lid actuator rod mounting clip and disconnect the rod from the trunk lid key lock cylinder assembly, then disconnect the electrical connector from the lock cylinder if equipped. Remove the mounting nuts and maneuver the lock cylinder out from the trunk lid, with installation being the reverse of removal. Next, disconnect the actuator rod from the trunk lid lock cylinder and the electrical connector from the trunk lid latch. Remove the latch mounting bolts and take out the latch, with installation again being the reverse of removal.