How to remove and install the Door Latch Assembly,Exterior Door Handle,Interior Door Handle and Door Lock Cylinder on Mazda 6?

Remove the door window glass and disconnect the cable from the negative battery terminal. Next, remove the door trim panel. For the outside door handle, take off the access hole cover and mounting screw, noting that on 2009 and later models, a stop prevents the screw from being removed. Rotate the latch rod and lock rod clips back to disconnect the rods from the outer handle, then pull the handle outwards. For 2008 and earlier models, remove the cover from the outside handle, and pull the handle out and to the rear to disengage it from the handle reinforcement inside the door. Remove the outside handle support mounting bolt from inside the door and take out the support. Inspect the outside door handle seals and replace them if they are cracked, torn, or deteriorated. Installation is the reverse of removal. For the inside door handle, pull the locking tab back, slide the shaft up, and detach the handle assembly from the door module, then disconnect the door lock cable from the inside door handle cable, with installation being the reverse of removal. To access the door latch, remove the outside door handle and disconnect the inside door handle and cables. Remove the door module mounting screws and take out the module, which includes the power window motor and window regulator. Disconnect the harness connector from the latch lock actuator if it wasn't done earlier, then disconnect the lock rod and latch rod from the door latch. Remove the door latch mounting screws and guide the latch assembly from the door, with installation being the reverse of removal. For the door lock cylinder on 2008 and earlier models, remove the door latch, rotate the lock cylinder counterclockwise until the tab fits into the notch opening, and pull the key lock cylinder out through the door, with installation being the reverse of removal. For 2009 and later models, remove the outside door handle, take out the access plug from the end of the door, and from the inside, remove the key lock rod clip and disconnect the rod from the key cylinder. Loosen the screw through the access hole from the end of the door, press the release tab on the inside of the door handle, and remove the lock cylinder from the door. Finally, separate the exterior trim cap from the key lock cylinder using a small screwdriver to disengage the tabs, with installation being the reverse of removal.

Genuine Mazda 6 Door Latch Assembly

Door Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

29 Door Latch Assemblys found

View related parts
Mazda 6 Lock Part Number: GK2A-56-820A
$81.50 MSRP: $108.68
You Save: $27.18 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock, Lid; Lock Assembly
- Replaces: GK2A-56-820
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2003-2008 Mazda 6 | Mazdaspeed, S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Lock Part Number: GS3L-58-310E
$108.54 MSRP: $144.75
You Save: $36.21 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Right), Door; Lock Actuator
- Position: Passenger Side
- Replaces: GS3L-58-310D, GS3L-58-310C, GS3L-58-310B
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: GJR9-59-310E
$93.85 MSRP: $125.17
You Save: $31.32 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Left), Door; Lock Actuator
- Position: Driver Side
- Replaces: GJR9-59-310A, GJR9-59-310B, GJR9-59-310D, GJR9-59-310
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Lock Part Number: GS3L-59-310E
$105.44 MSRP: $140.62
You Save: $35.18 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Left), Door; Lock Actuator
- Position: Driver Side
- Replaces: GS3L-59-310C, GS3L-59-310B, GS3L-59-310D
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2010 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: GS3N-73-310E
$125.31 MSRP: $167.12
You Save: $41.81 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Left), Door; Lock Actuator
- Position: Driver Side
- Replaces: GS3N-73-310D, GS3N-73-310A, GS3N-73-310B
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: GS3N-72-310E
$125.31 MSRP: $167.12
You Save: $41.81 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Right), Door; Lock Actuator
- Position: Passenger Side
- Replaces: GS3N-72-310A, GS3N-72-310D, GS3N-72-310B
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: GSYL-56-82XA
$103.68 MSRP: $138.26
You Save: $34.58 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock, Lid; Lock Assembly
- Replaces: GSYL-56-82X, GS3L-56-820A, GS3L-56-820
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2017 Mazda 6 | Grand Touring, S, Sport, Touring, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: GJR9-56-820
$59.35 MSRP: $79.15
You Save: $19.80 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock, Lid; Lock Assembly
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2016-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Lock Part Number: GJR9-58-310B
$93.85 MSRP: $125.17
You Save: $31.32 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Right), Door; Lock Actuator
- Position: Passenger Side
- Replaces: GJR9-58-310A, GJR9-58-310
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Lock Part Number: GEA3-58-310A
$116.79 MSRP: $155.75
You Save: $38.96 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Right), Door; Lock Actuator
- Position: Passenger Side
- Replaces: GEA3-58-310
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: GS3L-73-310E
$124.36 MSRP: $165.85
You Save: $41.49 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Left), Door; Lock Actuator
- Position: Driver Side
- Replaces: GS3L-73-310D, GS3L-73-310A, GS3L-73-310B, GS3L-73-310C
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: G22G-62-310M
$179.88 MSRP: $239.88
You Save: $60.00 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock, Lift Gate; Lock Assembly
- Replaces: G22G-62-310K, G22G-62-310H, G22G-62-310C, G22G-62-310G, G22G-62-310J, G22G-62-310B, G22G-62-310L
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2004-2008 Mazda 6 | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda 6 Lock Part Number: GS3L-72-310E
$125.31 MSRP: $167.12
You Save: $41.81 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Right), Door; Lock Actuator
- Position: Passenger Side
- Replaces: GS3L-72-310C, GS3L-72-310A, GS3L-72-310D, GS3L-72-310B
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2009-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: G44A-73-310A
$76.25 MSRP: $101.69
You Save: $25.44 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Left), Door; Lock Actuator
- Position: Driver Side
- Replaces: G44A-73-310
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Lock Part Number: G44A-72-310A
$84.49 MSRP: $112.68
You Save: $28.19 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Right), Door; Lock Actuator
- Position: Passenger Side
- Replaces: G44A-72-310
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Lock Part Number: GEA4-58-310A
$117.31 MSRP: $156.45
You Save: $39.14 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Right), Door; Lock Actuator
- Position: Passenger Side
- Replaces: GEA4-58-310
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: GEA3-59-310A
$118.83 MSRP: $158.47
You Save: $39.64 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Left), Door; Lock Actuator
- Position: Driver Side
- Replaces: GEA3-59-310
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2011-2013 Mazda 6 | S, i | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda 6 Lock Part Number: GJT1-73-310A
$124.46 MSRP: $165.98
You Save: $41.52 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Left), Door; Lock Actuator
- Position: Driver Side
- Replaces: GJT1-73-310
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Lock Part Number: GJT1-72-310A
$124.46 MSRP: $165.98
You Save: $41.52 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock(Right), Door; Lock Actuator
- Position: Passenger Side
- Replaces: GJT1-72-310
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2021 Mazda 6 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda 6 Lock Part Number: G21B-62-310H
$158.59 MSRP: $211.49
You Save: $52.90 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock, Lift Gate; Lock Assembly
- Replaces: G21B-62-310G, G21B-62-310, G21B-62-310E, G21B-62-310D, G21B-62-310F
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2004-2007 Mazda 6 | S, i | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

| Page 1 of 2 |Next >

1-20 of 29 Results

Mazda 6 Door Latch Assembly

The Mazda 6 Door Latch Assembly locks each door to the body of the vehicle to prevent unwanted entry while allowing the doors to be opened. Housed in the frame of the door, the device engages a striker on the body of the vehicle when the door closes, thus holding that panel so it won't swing open while driving. In a Mazda, the internal catches will release when either the inside or outside handle is actuated, allowing the door to open smoothly. The lock is compatible with the locking system of the vehicle, whether its manual intervention by the user, electronic activation, or a central circuit treating all doors together. The Door Latch Assembly provides the essential mechanical hold that secures occupants and keeps the cabin protected, no matter the actuation method. The design allows the door to close all by itself. First, it is pulled into position, and then it locks with a firm click. This mechanism disengages upon command so that clean opening is carried out smoothly without excessive force. The robust construction will be subjected to multiple repeated opening, latching, and unlatching cycles during the vehicle's life. The core safety feature of the Door Latch Assembly relies on this reliability applied in every Mazda door. With a solid grip under vibration, cornering and everyday use, it delivers the comfort and safety expected of 6 family cars from Mazda and performs consistently across the 6 range.

Looking for Door Latch Assembly with proven quality? Choose OEM Door Latch Assembly. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda 6 parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine 6 part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda 6 Door Latch Assembly Parts and Q&A

Lock
G22G-62-310M
Q:
How to remove and install the Door Latch Assembly,Exterior Door Handle,Interior Door Handle and Door Lock Cylinder on Mazda 6?
A:
Remove the door window glass and disconnect the cable from the negative battery terminal. Next, remove the door trim panel. For the outside door handle, take off the access hole cover and mounting screw, noting that on 2009 and later models, a stop prevents the screw from being removed. Rotate the latch rod and lock rod clips back to disconnect the rods from the outer handle, then pull the handle outwards. For 2008 and earlier models, remove the cover from the outside handle, and pull the handle out and to the rear to disengage it from the handle reinforcement inside the door. Remove the outside handle support mounting bolt from inside the door and take out the support. Inspect the outside door handle seals and replace them if they are cracked, torn, or deteriorated. Installation is the reverse of removal. For the inside door handle, pull the locking tab back, slide the shaft up, and detach the handle assembly from the door module, then disconnect the door lock cable from the inside door handle cable, with installation being the reverse of removal. To access the door latch, remove the outside door handle and disconnect the inside door handle and cables. Remove the door module mounting screws and take out the module, which includes the power Window Motor and Window Regulator. Disconnect the harness connector from the latch lock actuator if it wasn't done earlier, then disconnect the lock rod and latch rod from the door latch. Remove the door latch mounting screws and guide the latch assembly from the door, with installation being the reverse of removal. For the door lock cylinder on 2008 and earlier models, remove the door latch, rotate the lock cylinder counterclockwise until the tab fits into the notch opening, and pull the key lock cylinder out through the door, with installation being the reverse of removal. For 2009 and later models, remove the outside door handle, take out the access plug from the end of the door, and from the inside, remove the key lock rod clip and disconnect the rod from the key cylinder. Loosen the screw through the access hole from the end of the door, press the release tab on the inside of the door handle, and remove the lock cylinder from the door. Finally, separate the exterior trim cap from the key lock cylinder using a small screwdriver to disengage the tabs, with installation being the reverse of removal.

Related Mazda 6 Parts

Browse by Year

2021 Door Latch Assembly 2020 Door Latch Assembly 2019 Door Latch Assembly 2018 Door Latch Assembly 2017 Door Latch Assembly 2016 Door Latch Assembly 2015 Door Latch Assembly 2014 Door Latch Assembly 2013 Door Latch Assembly 2012 Door Latch Assembly 2011 Door Latch Assembly 2010 Door Latch Assembly 2009 Door Latch Assembly 2008 Door Latch Assembly 2007 Door Latch Assembly 2006 Door Latch Assembly 2005 Door Latch Assembly 2004 Door Latch Assembly 2003 Door Latch Assembly

Genuine Mazda 6 Door Latch Assembly

29 Door Latch Assemblys found

Mazda 6 Lock Part Number: GK2A-56-820A

Mazda 6 Lock Part Number: GS3L-58-310E

Mazda 6 Lock Part Number: GJR9-59-310E

Mazda 6 Lock Part Number: GS3L-59-310E

Mazda 6 Lock Part Number: GS3N-73-310E

Mazda 6 Lock Part Number: GS3N-72-310E

Mazda 6 Lock Part Number: GSYL-56-82XA

Mazda 6 Lock Part Number: GJR9-56-820

Mazda 6 Lock Part Number: GJR9-58-310B

Mazda 6 Lock Part Number: GEA3-58-310A

Mazda 6 Lock Part Number: GS3L-73-310E

Mazda 6 Lock Part Number: G22G-62-310M

Mazda 6 Lock Part Number: GS3L-72-310E

Mazda 6 Lock Part Number: G44A-73-310A

Mazda 6 Lock Part Number: G44A-72-310A

Mazda 6 Lock Part Number: GEA4-58-310A

Mazda 6 Lock Part Number: GEA3-59-310A

Mazda 6 Lock Part Number: GJT1-73-310A

Mazda 6 Lock Part Number: GJT1-72-310A

Mazda 6 Lock Part Number: G21B-62-310H

Mazda 6 Door Latch Assembly

Mazda 6 Door Latch Assembly Parts and Q&A

Related Mazda 6 Parts

Browse by Year