How to test and replace an front ABS Sensor on Mazda B2200?

In order to test the ABS Sensor, disconnect the wire harness plug on the sensor or the pigtail. Next, put Digital Volt/Ohm Meter (DVOM) on the two terminals of the ABS Sensor and note the value, which has to be in the range of 0.270-0.330k ohms. To remove and install, begin by unplugging the ABS Sensor from the harness in the engine compartment. The second step is to unclip the ABS sensor cable of the brake hose clips, and remove the retaining bolt of the spindle to slide the ABS Sensor out of its hole. To install, repeat the steps to remove and tighten the retaining bolt of 40-60 inch lbs. (5-7Nm).

How to replace the ABS Sensor and its components on Mazda Millenia?

A magnetic ABS sensor is placed on each wheel at a fixed distance to a toothed ring which is rotating with the wheel. The sensors can be changed but they should be installed at their articulated positions whereas the toothed rings can be changed too but this would demand disassembling of the hub or axle shaft. To remove and install, safely support and raise the vehicle, and then take out the wheel. Disconnect the connector, undo the mounting bolts / nuts and withdraw the ABS sensor. In installation, undo the steps of removal, screw 12-16 ft. lbs. (16-22 Nm) sensor bolts tighter. When it comes to the Millenia, the first thing to do would be to unplug the electrical connector of the ABS sensor under the hood and then lift up and support the vehicle so as to get rid of the tire and wheel. Disconnect the ABS sensor wire bracket and the two nuts with the body, and then the two nuts connecting the two nuts to the ABS sensor wire clamp. Take off the grommet and the ABS sensor wire, located in the engine compartment, and remove the bolt that connects the ABS sensor wire clamp with the knuckle as well as remove the ABS sensor. To install, attach the ABS sensor by screwing it to 14-18 ft. lbs. (19-25 Nm) with its mounting bolt and verify the clearance between the ABS sensor and the sensor rotor and ensure it is not exceeding 0.012-0.043 in. (0.3-1.1 mm). Otherwise, change the sensor rotor or ABS sensor. Reconnect the ABS sensor wire clamp to the steering knuckle and then feed the ABS sensor wire back into the engine compartment, re-fit the grommet, and fasten the wire clamps with the strut bracket and body bracket and tighten all the nuts to 70-95.4 in. lbs. (7.9-10.7 Nm). Lastly, replace the tire and wheel, lower the vehicle and reconnect the electrical connector of the ABS sensor. To take off the rear, unplug the electrical connector of the ABS sensor, remove the bolts holding the strut assembly and ABS sensor wire clamps to the body, remove the mounting bolt of the sensor and remove the ABS sensor. The procedures are reinstallation in the same order followed by mounting bolt and wire clamp mounting bolts tightened to 14-18 ft. lbs. (19-25 Nm).

Genuine Mazda ABS Sensor

ABS Wheel Speed Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

169 ABS Sensors found

View related parts
Mazda ABS Sensor Part Number: KA0G-43-7EYA
$122.23 MSRP: $163.00
You Save: $40.77 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Harness, Epb(Left)
- Position: Driver Side
Fits the following Mazda Models:
- CX-5 | 2017-2021 | Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: KA0G-43-7EXA
$132.14 MSRP: $176.21
You Save: $44.07 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Harness, Epb(Right)
- Position: Passenger Side
- Replaces: KA0G-43-7EX
Fits the following Mazda Models:
- CX-5 | 2017-2021 | Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: GHP9-43-71Y
$51.35 MSRP: $68.49
You Save: $17.14 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Rear-A.B.S.; Rear Speed Sensor
Fits the following Mazda Models:
- 6 | 2014-2017 | Grand Touring, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: KA0G-43-70X
$56.54 MSRP: $75.39
You Save: $18.85 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Right), Front-A.B.S.; Front Speed Sensor
Fits the following Mazda Models:
- CX-5 | 2017-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: TK79-43-7EY
$78.39 MSRP: $104.53
You Save: $26.14 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Harness, Epb(Left)
- Position: Driver Side
Fits the following Mazda Models:
- CX-9 | 2016-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: TK79-43-7EX
$79.45 MSRP: $105.95
You Save: $26.50 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Harness, Epb(Right)
- Position: Passenger Side
Fits the following Mazda Models:
- CX-9 | 2016-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: N243-43-70XB
$104.99 MSRP: $140.01
You Save: $35.02 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Right), Front-A.B.S.; Front Speed Sensor
- Position: Passenger Side
Fits the following Mazda Models:
- MX-5 Miata | 2016-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda ABS Sensor Part Number: N243-43-71YB
$107.53 MSRP: $143.39
You Save: $35.86 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Right), Rear-A.B.S.; Rear Speed Sensor
- Position: Passenger Side
- Replaces: N243-43-71YA
Fits the following Mazda Models:
- MX-5 Miata | 2016-2023 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda ABS Sensor Part Number: TK78-43-70X
$121.90 MSRP: $162.57
You Save: $40.67 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Right), Front-A.B.S.; Front Speed Sensor
Fits the following Mazda Models:
- CX-9 | 2016-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: D10H-43-72YB
$50.90 MSRP: $67.88
You Save: $16.98 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Left), Rear-A.B.S.; Rear Speed Sensor
- Position: Driver Side
Fits the following Mazda Models:
- CX-3 | 2016-2018 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda ABS Sensor Part Number: D10K-43-71Y
$57.30 MSRP: $76.41
You Save: $19.11 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Right), Rear-A.B.S.; Rear Speed Sensor
Fits the following Mazda Models:
- CX-3 | 2016-2018 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda ABS Sensor Part Number: K017-43-71YA
$60.69 MSRP: $80.92
You Save: $20.23 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Right), Rear-A.B.S.; Rear Speed Sensor
- Replaces: K017-43-71Y
Fits the following Mazda Models:
- CX-5 | 2013-2015 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: BP4K-43-701A
$80.31 MSRP: $107.11
You Save: $26.80 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Front), A.B.S.; Front Speed Sensor
- Replaces: BP4K-43-701
Fits the following Mazda Models:
- 3 | 2004-2013 | Mazdaspeed, S, SP23, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
- 5 | 2012-2015, 2006-2010 | Grand Touring, Sport, Touring | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: D10H-43-71YB
$43.43 MSRP: $57.92
You Save: $14.49 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Right), Rear-A.B.S.; Rear Speed Sensor
- Position: Passenger Side
Fits the following Mazda Models:
- CX-3 | 2016-2018 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda ABS Sensor Part Number: D10E-43-70X
$137.96 MSRP: $183.99
You Save: $46.03 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Right), Front-A.B.S.; Front Speed Sensor
Fits the following Mazda Models:
- CX-3 | 2016-2021 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda ABS Sensor Part Number: K011-43-70XA
$52.10 MSRP: $69.49
You Save: $17.39 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Right, Front A.B.S.; Front Speed Sensor
- Replaces: K011-43-70X
Fits the following Mazda Models:
- 6 | 2014-2021 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
- CX-5 | 2013-2016 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: B45G-43-71Y
$31.90 MSRP: $42.54
You Save: $10.64 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Rear-A.B.S.; Rear Speed Sensor
Fits the following Mazda Models:
- 3 | 2014-2018 | Grand Touring, I Sport, I Touring, Sport, Touring, i Grand Touring, i SV, s Grand Touring, s Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: BDTS-43-70X
$38.23 MSRP: $50.98
You Save: $12.75 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor(Right), Front-A.B.S.; Front Speed Sensor
Fits the following Mazda Models:
- 3 | 2019-2025 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda ABS Sensor Part Number: D24R-43-7EX
$93.04 MSRP: $124.08
You Save: $31.04 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Harness, Epb(Right)
- Position: Passenger Side
Fits the following Mazda Models:
- CX-3 | 2019-2021 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda ABS Sensor Part Number: BAAN-43-7EXC
$118.25 MSRP: $157.70
You Save: $39.45 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Harness, Epb(Right)
- Position: Passenger Side
- Replaces: BAAN-43-7EX, BAAN-43-7EXB
Fits the following Mazda Models:
- 3 | 2017-2018 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS

| Page 1 of 9 |Next >

1-20 of 169 Results

Mazda ABS Sensor

The ABS Sensor monitors the speed of the wheels at all times to prevent locking up, giving every Mazda driver confidence in braking. Mazda has earned its reputation thanks to lively handling, beautiful KODO styling and SKYACTIV powertrains that offer a bit of everyday excitement while keeping costs down. With a complete suite of safety features including i-ACTIVSENSE driver aids and robust chassis engineering, the brand ensures that both vehicle occupants and pedestrians feel at ease. Mazda's emphasis on constructing lighter cars with good steering and well-tuned suspension means that you feel close and connected to the vehicle at all times, making every journey rewarding. Mazda aims to lower emissions and enhance electrification while ensuring that new models will deliver the same zest for driving. Although these benefits of the company define it, the ABS Sensor adds to this. It maintains control when traction fails. This small component sits next to a notched ring at each wheel hub. The component reads changes in the magnetic field and converts them into voltage pulses. The pulses show how quickly each wheel turns or slows down. The control module continuously compares those signals to fine-tune hydraulic pressure, thus keeping the wheels rolling instead of skidding and preserving steering authority and stability. Even at low speeds where magnetic distortion is not strong, the ABS Sensor receives critical data which helps the braking system to stop uniformly. With its robustness and self-monitoring capabilities, it supports the entire Mazda lineup by means of fast and reliable feedback that boosts safety while keeping up with the effective drive that Mazda promises.

You'll get great performance and real durability when you pick genuine OEM ABS Sensor. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda ABS Sensor Parts and Q&A

Speed Sensor
LA31-43-711
Q:
How to test and replace an front ABS Sensor on Mazda B2200?
A:
In order to test the ABS Sensor, disconnect the wire harness plug on the sensor or the pigtail. Next, put Digital Volt/Ohm Meter (DVOM) on the two terminals of the ABS Sensor and note the value, which has to be in the range of 0.270-0.330k ohms. To remove and install, begin by unplugging the ABS Sensor from the harness in the engine compartment. The second step is to unclip the ABS sensor cable of the brake hose clips, and remove the retaining bolt of the spindle to slide the ABS Sensor out of its hole. To install, repeat the steps to remove and tighten the retaining bolt of 40-60 inch lbs. (5-7Nm).
Front Speed Sensor
TA01-43-70XF
Q:
How to replace the ABS Sensor and its components on Mazda Millenia?
A:
A magnetic ABS sensor is placed on each wheel at a fixed distance to a toothed ring which is rotating with the wheel. The sensors can be changed but they should be installed at their articulated positions whereas the toothed rings can be changed too but this would demand disassembling of the hub or axle shaft. To remove and install, safely support and raise the vehicle, and then take out the wheel. Disconnect the connector, undo the mounting bolts / nuts and withdraw the ABS sensor. In installation, undo the steps of removal, screw 12-16 ft. lbs. (16-22 Nm) sensor bolts tighter. When it comes to the Millenia, the first thing to do would be to unplug the electrical connector of the ABS sensor under the hood and then lift up and support the vehicle so as to get rid of the tire and wheel. Disconnect the ABS sensor wire bracket and the two nuts with the body, and then the two nuts connecting the two nuts to the ABS sensor wire clamp. Take off the grommet and the ABS sensor wire, located in the engine compartment, and remove the bolt that connects the ABS sensor wire clamp with the knuckle as well as remove the ABS sensor. To install, attach the ABS sensor by screwing it to 14-18 ft. lbs. (19-25 Nm) with its mounting bolt and verify the clearance between the ABS sensor and the sensor rotor and ensure it is not exceeding 0.012-0.043 in. (0.3-1.1 mm). Otherwise, change the sensor rotor or ABS sensor. Reconnect the ABS sensor wire clamp to the steering knuckle and then feed the ABS sensor wire back into the engine compartment, re-fit the grommet, and fasten the wire clamps with the strut bracket and body bracket and tighten all the nuts to 70-95.4 in. lbs. (7.9-10.7 Nm). Lastly, replace the tire and wheel, lower the vehicle and reconnect the electrical connector of the ABS sensor. To take off the rear, unplug the electrical connector of the ABS sensor, remove the bolts holding the strut assembly and ABS sensor wire clamps to the body, remove the mounting bolt of the sensor and remove the ABS sensor. The procedures are reinstallation in the same order followed by mounting bolt and wire clamp mounting bolts tightened to 14-18 ft. lbs. (19-25 Nm).