How to remove the rack and pinions from the steering gear on Mazda 3?

To take out the rack and pinions, disconnect the cable in the negative terminal of the battery at first. Disconnect the ends of the tie-rods of the steering knuckles, with an Allen wrench to hold the stud in case the ballstud spins with the nut. Disconnect the lower control arm at the steering knuckle, and seal off the extremities to prevent loss and contamination of the fluid. Other models could contain a sheetmetal shield that is held by bolts that must be removed to access the fittings. Then, undo the mounting throughbolt of the rear engine and prop the crossmember using a floor jack. Unscrew the fasteners on the lower mount, and re-screw the upper mounting bolts, and drop the crossmember, with jackstands on each side. Be careful since the crossmember is very heavy and it should be supported by the jack. Disassemble the shield when fitted and the three rack and pinions fitting bolts and then lift the rack and pinions off the crossmember and out of the car. To install, go in reverse of the steps during removal, but make sure to line the matchmarks when hooking the rack and pinions input shaft up to the intermediate shaft U-joint. Install a fresh banjo bolt and sealing washers to the power steering pressure line, check all fasteners to the correct torque values and pour in the proper fluid in the power steering reservoir. Last but not least, drain the power steering hydraulic system and ensure a front-end check-up and adjustment when needed.

Genuine Mazda 3 Rack and Pinions

Steering Rack

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Rack and Pinions found

View related parts
Mazda 3 Rack Part Number: B32H-32-119
$185.94 MSRP: $247.97
You Save: $62.03 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rack, Steering Gear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2007-2008 Mazda 3 | Mazdaspeed | 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Rack Part Number: BBM4-32-119
$199.68 MSRP: $266.29
You Save: $66.61 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rack, Steering Gear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2010-2013 Mazda 3 | i, Mazdaspeed, S | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Steering Gear Part Number: GHT2-32-110E
$278.55 MSRP: $371.47
You Save: $92.92 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear, Steering; Gear Assembly
- Replaces: BJS7-32-110B, BJS7-32-110, BJS7-32-110A, BJS8-32-110, GHT2-32-110D, GHT2-32-110B, GHT2-32-110, GHT2-32-110A, GHT2-32-110C
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2018 Mazda 3 | Grand Touring, i Grand Touring, I Sport, i SV, I Touring, s Grand Touring, s Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Steering Gear Part Number: BCKA-32-110B
$285.03 MSRP: $380.10
You Save: $95.07 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear, Steering; Gear Assembly, Steering Gear
- Replaces: BCKA-32-110A, BCKA-32-110
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2019-2024 Mazda 3 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Rack Part Number: BP4L-32-119
$291.39 MSRP: $388.59
You Save: $97.20 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rack, Steering Gear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2004-2009 Mazda 3 | i, Mazdaspeed, S, SP23 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Steering Gear Part Number: BDTS-32-110B
$353.30 MSRP: $471.16
You Save: $117.86 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear, Steering; Gear Assembly, Steering Gear
- Replaces: BDTS-32-110
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2019-2024 Mazda 3 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Steering Gear Part Number: CC29-32-110R-0C
Product Specifications
- Other Name: Reman, Gear Steering; Gear Assembly
- Replaces: CC29-32-110R-0A, CC29-32-110C, BR5V-32-110A, BR5V-32-110, CC29-32-110A, CC29-32-110B
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mazda 3 | i, Mazdaspeed, S | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Steering Gear Part Number: BBN6-32-110B
Product Specifications
- Other Name: Gear, Steering; Gear Assembly
- Replaces: BBN6-32-110, BBN6-32-110A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2010-2013 Mazda 3 | Mazdaspeed | 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Steering Gear Part Number: BBM4-32-110R-0G
Product Specifications
- Other Name: Reman, Gear Steering; Gear Assembly
- Replaces: BBM4-32-110C, BBM4-32-110B, BBM4-32-110R-0C, BBM4-32-110, BBM4-32-110A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2010-2013 Mazda 3 | i, Mazdaspeed, S | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Steering Gear Part Number: BP4L-32-110R-00
Product Specifications
- Other Name: Gear, Steering W/O Sensor; Steering Gear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2004-2006 Mazda 3 | i, S, SP23 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Steering Gear Part Number: BR6J-32-110D
Product Specifications
- Other Name: Gear, Steering; Gear Assembly
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2007-2009 Mazda 3 | i, Mazdaspeed, S | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Pinion Shaft Part Number: GHT2-32-12Y
Product Specifications
- Other Name: Pinion, Steering Gear; Pinion Shaft
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014 Mazda 3 | i Grand Touring, I Sport, i SV, I Touring, s Grand Touring, s Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS

Mazda 3 Rack and Pinions

Looking for Rack and Pinions with proven quality? Choose OEM Rack and Pinions. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda 3 parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine 3 part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda 3 Rack and Pinions Parts and Q&A

Steering Gear
CC29-32-110R-0C
Q: How to remove the rack and pinions from the steering gear on Mazda 3?
A:
To take out the rack and pinions, disconnect the cable in the negative terminal of the battery at first. Disconnect the ends of the tie-rods of the Steering Knuckles, with an Allen wrench to hold the stud in case the ballstud spins with the nut. Disconnect the lower Control Arm at the steering knuckle, and seal off the extremities to prevent loss and contamination of the fluid. Other models could contain a sheetmetal shield that is held by bolts that must be removed to access the fittings. Then, undo the mounting throughbolt of the rear engine and prop the crossmember using a floor jack. Unscrew the fasteners on the lower mount, and re-screw the upper mounting bolts, and drop the crossmember, with jackstands on each side. Be careful since the crossmember is very heavy and it should be supported by the jack. Disassemble the shield when fitted and the three rack and pinions fitting bolts and then lift the rack and pinions off the crossmember and out of the car. To install, go in reverse of the steps during removal, but make sure to line the matchmarks when hooking the rack and pinions input shaft up to the intermediate shaft U-joint. Install a fresh banjo bolt and sealing washers to the power steering pressure line, check all fasteners to the correct torque values and pour in the proper fluid in the power steering reservoir. Last but not least, drain the power steering hydraulic system and ensure a front-end check-up and adjustment when needed.