How to disconnect and replace the shift cable on Mazda 3?

Detach the cable from the battery's negative terminal. Remove the upper engine cover by pulling it up from each side and lifting it off the mounting posts in the center. Remove battery and battery tray and then center console. To disconnect the shift cable from the shift lever and remove the retaining clip, pry the end of the cables off the manual shift lever arm at the transaxle. Carefully loosen the cable housing ends at the transaxle from the support bracket without damaging the plastic flanges. Extract the fasteners holding the transmission cable plate/grommet, where the cable goes through the floor. Pull the shift cable through from inside remembering the grommet is part of the cable assembly. To install it, reverse the steps for removal and adjust the new cable later. In order to make this adjustment, take the center console out, switch the shifter to the Park position and then move the shift arm at the transaxle three clicks to counterclockwise so it is in Park. The adjuster mechanism of the shift cable is on the inside end. The safety lock can be slid back and the lock piece moved outwards. The lock piece is then pressed into the cable, and the safety lock is slid into place. This must snap firmly. After reinstalling any leftover parts, set the parking brake and move the car in each range to make sure the adjustment is correct.

How to replace the components and adjust the new Shift Cable after installation on Mazda 3?

Before replacing the components, disconnect the cable from the negative battery terminal. The next step is to remove the upper engine cover - lift it upward, on each side, and remove it from the center mounting posts. After that, the battery and the battery tray and then the center console. Take off the shift lever and remove the shift cables from the shift lever. Pry off the ends of the cables from the shift lever arm ball studs at the transaxle. Some models contain spring clips that can be rotated, making removal easier. Be sure not to damage the clips. Detach the ends of the cable housing located at the transaxle from the support bracket, taking care to avoid damaging the plastic flanges of the cable housing. Detach the fasteners holding the transmission cable plate/grommet on the inside at the floor where the cable passes through, then pull the shift cables through from the inside. Note that the grommet is part of the cable assembly. The process of installation is the opposite of removal. Furthermore, adjust the new cable after installation. In order to perform the adjustment, the parking brake should be set. Further, remove the gearshift knob and the center console trim panel. Move the safety lock away from the shifter ball stud and the cable lock away from the end fitting of the shift cable. Ensure that the shift lever is in the center position so that the lever and the transaxle are in Neutral. Push the cable lock onto the cable, slide the safety lock over the primary shift cable lock, and then, reinstall the center console trim panel and gearshift knob.

Genuine Mazda 3 Shift Cable

Transmission Shift Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Shift Cables found

View related parts
Mazda 3 Cable Assembly Part Number: BN8E-46-500B
$198.16 MSRP: $264.28
You Save: $66.12 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Control Cable; Shift Control Cable
- Replaces: B32T-46-500, B32T-46-500A, BN8E-46-500, BN8E-46-500A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2004-2009 Mazda 3 | S, SP23, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Cable Part Number: BDTV-46-500D
$47.33 MSRP: $63.12
You Save: $15.79 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Shift Control Cable
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2024-2025 Mazda 3 | 2.5 S, Carbon Edition, Preferred, Premium, Select Sport | 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Cable Part Number: DEKK-46-500
$64.59 MSRP: $86.14
You Save: $21.55 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Shift Control Cable
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2022-2025 Mazda 3 | 2.5 Carbon Turbo, 2.5 Turbo, 2.5 Turbo Premium Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Cable Part Number: BDTV-46-500C
$76.26 MSRP: $101.71
You Save: $25.45 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Shift Control Cable
- Replaces: BCKA-46-500B, BDTV-46-500B, BCKA-46-500C
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2019-2023 Mazda 3 | 2.0, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Cable Part Number: BFWM-46-500
$110.66 MSRP: $147.59
You Save: $36.93 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Cable Bracket, Shift Control Cable
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2021-2025 Mazda 3 | 2.5 Carbon Turbo, 2.5 Turbo, 2.5 Turbo Premium Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Cable, Control Part Number: GHK3-46-500A
$121.73 MSRP: $162.33
You Save: $40.60 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CABLE,CONTROL; Cable, Control Cable, Shift Control Cable
- Replaces: GHK3-46-500
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2018 Mazda 3 | Grand Touring, I Sport, I Touring, Sport, Touring, i Grand Touring, i SV, s Grand Touring, s Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Cable Part Number: BCKA-46-500D
$126.98 MSRP: $169.34
You Save: $42.36 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Shift Control Cable
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2023-2025 Mazda 3 | 2.5 S, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Control Cable Part Number: BJS9-46-500
$152.13 MSRP: $202.88
You Save: $50.75 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Shift Control Cable
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2018 Mazda 3 | Grand Touring, I Sport, I Touring, Sport, Touring, i Grand Touring, i SV, s Grand Touring, s Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Cable Assembly Part Number: BR9L-46-500B
$171.56 MSRP: $228.80
You Save: $57.24 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Shift Control Cable
- Replaces: BR9L-46-500, BR9L-46-500A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mazda 3 | Mazdaspeed, S | 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Cable Part Number: GHK1-46-500
$180.63 MSRP: $240.89
You Save: $60.26 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Control Cable, Shift Control Cable
- Replaces: BJS7-46-500A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2014-2018 Mazda 3 | Grand Touring, I Sport, I Touring, Sport, Touring, i Grand Touring, i SV, s Grand Touring, s Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Cable Part Number: BCKN-46-500C
$318.86 MSRP: $425.24
You Save: $106.38 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Shift Control Cable
- Replaces: BCKN-46-500B
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2019-2024 Mazda 3 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Cable Assembly Part Number: B37F-46-500D
$450.53 MSRP: $605.67
You Save: $155.14 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control; Shift Control Cable
- Replaces: B37F-46-500A, B37F-46-500C
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2007-2009 Mazda 3 | Mazdaspeed | 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Cable Assembly Part Number: BP4S-46-500F
$457.94 MSRP: $615.65
You Save: $157.71 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Control Cable; Shift Control Cable
- Replaces: BP4S-46-500D, BP4S-46-500E, BP4S-46-500A, BP4S-46-500C
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2004-2006 Mazda 3 | S, SP23, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Shift Control Cable Part Number: BBM3-46-500E
$188.03 MSRP: $250.75
You Save: $62.72 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control
- Replaces: BBM3-46-500B, BBM3-46-500D
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2010-2013 Mazda 3 | S, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Shift Control Cable Part Number: BACV-46-500
$94.75 MSRP: $126.35
You Save: $31.60 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2018 Mazda 3 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Shift Control Cable Part Number: BFD2-46-500
$170.79 MSRP: $227.76
You Save: $56.97 (26%)
ADD TO CART
Product Specifications
- Other Name: Cable, Control
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Mazda 3 | S, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Shift Control Cable Part Number: BBM2-46-500F
$343.63 MSRP: $458.26
You Save: $114.63 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control
- Replaces: BBM2-46-500D, BBM2-46-500B
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2010-2013 Mazda 3 | S, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda 3 Shift Control Cable Part Number: BBP8-46-500F
$352.40 MSRP: $469.97
You Save: $117.57 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Control
- Replaces: BBP8-46-500D, BBP8-46-500E
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2010-2013 Mazda 3 | Mazdaspeed | 4 Cyl 2.3 L GAS
View related parts
Mazda 3 Shift Control Cable Part Number: BFD1-46-500
Product Specifications
- Other Name: Cable, Control
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2012-2013 Mazda 3 | i | 4 Cyl 2.0 L GAS
View related parts
Mazda 3 Cable Assembly Part Number: BAK6-46-500A
Product Specifications
- Other Name: Cable, Control; Shift Control Cable
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2006-2009 Mazda 3 | S, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS

Mazda 3 Shift Cable

The Mazda 3 Shift Cable assists the driver in moving the gear selector to the transmission, ensuring correct engagement between the chosen gear. A steel wire runs through the flexible outer sheath that moves with every movement of the lever. Thus, the manual input of the hand creates an actual mechanical movement at the transmission end. A cable linking the floor-mounted shifter to internal shift components in a front-wheel-drive Mazda with a manual transaxle carries forward, backward, and sideways lever motion to move shift forks and shift collars across the gears. Mazda vehicles with automatic transmission use a selector cable that connects the floor or column lever to the manual lever in the transmission case. It uses the standard PRNDL pattern and allows range changes only after the driver operates the release. A Mazda that includes an electronic shift interlock still uses a mechanical cable to hold the transaxle in Park until the brake pedal is pushed. This enhances safety but does not change the basic layout of the cables. The Shift Cable contains an inner wire and an outer sheath resistant to kinking and corrosion and low friction to keep shift effort consistent. A damaged Shift Cable can cause you to feel the gear stick loosen or pop out of gear. The cabling may even refuse to engage due to stretch, break, or bending. These effects can happen even on a short 3-mile trip. Wear is indicated by a detectable looseness of more than about 3 mm, while a Mazda cable inspection ensures confidence.

Looking for Shift Cable with proven quality? Choose OEM Shift Cable. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda 3 parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine 3 part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda 3 Shift Cable Parts and Q&A

Cable Assembly
BAK6-46-500A
Q:
How to disconnect and replace the shift cable on Mazda 3?
A:
Detach the cable from the battery's negative terminal. Remove the upper engine cover by pulling it up from each side and lifting it off the mounting posts in the center. Remove battery and battery tray and then center console. To disconnect the shift cable from the shift lever and remove the retaining clip, pry the end of the cables off the manual shift lever arm at the transaxle. Carefully loosen the cable housing ends at the transaxle from the support bracket without damaging the plastic flanges. Extract the fasteners holding the transmission cable plate/grommet, where the cable goes through the floor. Pull the shift cable through from inside remembering the grommet is part of the cable assembly. To install it, reverse the steps for removal and adjust the new cable later. In order to make this adjustment, take the center console out, switch the shifter to the Park position and then move the shift arm at the transaxle three clicks to counterclockwise so it is in Park. The adjuster mechanism of the shift cable is on the inside end. The safety lock can be slid back and the lock piece moved outwards. The lock piece is then pressed into the cable, and the safety lock is slid into place. This must snap firmly. After reinstalling any leftover parts, set the parking brake and move the car in each range to make sure the adjustment is correct.
Cable Assembly
B37F-46-500D
Q:
How to replace the components and adjust the new Shift Cable after installation on Mazda 3?
A:
Before replacing the components, disconnect the cable from the negative battery terminal. The next step is to remove the upper engine cover - lift it upward, on each side, and remove it from the center mounting posts. After that, the battery and the battery tray and then the center console. Take off the shift lever and remove the shift cables from the shift lever. Pry off the ends of the cables from the shift lever arm ball studs at the transaxle. Some models contain spring clips that can be rotated, making removal easier. Be sure not to damage the clips. Detach the ends of the cable housing located at the transaxle from the support bracket, taking care to avoid damaging the plastic flanges of the cable housing. Detach the fasteners holding the transmission cable plate/grommet on the inside at the floor where the cable passes through, then pull the shift cables through from the inside. Note that the grommet is part of the cable assembly. The process of installation is the opposite of removal. Furthermore, adjust the new cable after installation. In order to perform the adjustment, the parking brake should be set. Further, remove the gearshift knob and the center console trim panel. Move the safety lock away from the shifter ball stud and the cable lock away from the end fitting of the shift cable. Ensure that the shift lever is in the center position so that the lever and the transaxle are in Neutral. Push the cable lock onto the cable, slide the safety lock over the primary shift cable lock, and then, reinstall the center console trim panel and gearshift knob.

Related Mazda 3 Parts

Browse by Year

2025 Shift Cable 2024 Shift Cable 2023 Shift Cable 2022 Shift Cable 2021 Shift Cable 2020 Shift Cable 2019 Shift Cable 2018 Shift Cable 2017 Shift Cable 2016 Shift Cable 2015 Shift Cable 2014 Shift Cable 2013 Shift Cable 2012 Shift Cable 2011 Shift Cable 2010 Shift Cable 2009 Shift Cable 2008 Shift Cable 2007 Shift Cable 2006 Shift Cable 2005 Shift Cable 2004 Shift Cable

Genuine Mazda 3 Shift Cable

20 Shift Cables found

Mazda 3 Cable Assembly Part Number: BN8E-46-500B

Mazda 3 Cable Part Number: BDTV-46-500D

Mazda 3 Cable Part Number: DEKK-46-500

Mazda 3 Cable Part Number: BDTV-46-500C

Mazda 3 Cable Part Number: BFWM-46-500

Mazda 3 Cable, Control Part Number: GHK3-46-500A

Mazda 3 Cable Part Number: BCKA-46-500D

Mazda 3 Control Cable Part Number: BJS9-46-500

Mazda 3 Cable Assembly Part Number: BR9L-46-500B

Mazda 3 Cable Part Number: GHK1-46-500

Mazda 3 Cable Part Number: BCKN-46-500C

Mazda 3 Cable Assembly Part Number: B37F-46-500D

Mazda 3 Cable Assembly Part Number: BP4S-46-500F

Mazda 3 Shift Control Cable Part Number: BBM3-46-500E

Mazda 3 Shift Control Cable Part Number: BACV-46-500

Mazda 3 Shift Control Cable Part Number: BFD2-46-500

Mazda 3 Shift Control Cable Part Number: BBM2-46-500F

Mazda 3 Shift Control Cable Part Number: BBP8-46-500F

Mazda 3 Shift Control Cable Part Number: BFD1-46-500

Mazda 3 Cable Assembly Part Number: BAK6-46-500A

Mazda 3 Shift Cable

Mazda 3 Shift Cable Parts and Q&A

Related Mazda 3 Parts

Browse by Year