How to remove the engine mount bracket and insulator on Mazda Tribute?

This procedure is essentially the same as for the four-cylinder engine. Follow the outlined steps, removing the engine mount bracket bolts to separate the bracket from the engine and insulator, and then remove the engine mount insulator bolts to separate the insulator from the engine compartment.

Do engine mounts seldom require attention, and should broken or deteriorated mounts be replaced immediately to prevent damage or wear on driveline components on Mazda Tribute?

Engine mounts do not need much time, but when they are broken or worn, they should be immediately changed to avoid damage and deterioration of the elements driving the engine. The engine should be lifted a little bit during the check in order to clear the mounts. Lift the vehicle up and rest it safely on jackstands, then place a jack under the engine oil pan with a large wood block between the jack head and the oil pan to avoid being damaged and take care not to lift up the engine to the point of removing all the weight on the mounts. Check the mounts, looking at them to identify cracks, hardened rubber, or separation of the material, rubber can crack along the lines. Test the relative motion between the mount plates and the engine or frame by a large screwdriver or pry bar; when motion is experienced, remove the engine and loosen the mount fasteners. Rubber preservative can be used to deteriorate. To replace, unscrew the battery cable on the negative terminal, and then lift the car and place it on jackstands unless it is already there. Lift the engine cover carefully so as to disconnect it with the ballstuds and remove it where it is present. Disassemble engine splash shield fasteners and disassemble splash shield underneath the vehicle, where fitted. With later models, the coolant reservoir can be unclipped, then moved aside without needing to disconnect the coolant lines. Position a floor jack beneath the engine with a block of wood in-between the jack head and oil pan to take the weight off the mounts. Unscrew the fasteners and remove the mount and frame and engine making sure that one of the mounts is not unscrewed unless the engine is removed. Installment is the opposite of removal where thread locking compound is applied on the mount bolts and tightened. Once the battery is reconnected, the Powertrain Control Module has to re-learn the idle and fuel trim strategy in order to provide optimal driving experience and performance.

Genuine Mazda Tribute Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

52 Engine Mounts found

View related parts
Mazda Tribute Mount Brace Part Number: EC02-39-023
$27.10 MSRP: $36.14
You Save: $9.04 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket(Up), Engine
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX | 4 Cyl 2.0 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EC02-39-020
$27.24 MSRP: $36.32
You Save: $9.08 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket No.2, Engine; Mount Bracket
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX | 4 Cyl 2.0 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EF91-39-080
$28.73 MSRP: $38.31
You Save: $9.58 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket No.4, Engine; Mount Bracket
- Position: Rear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011, 2005-2006 Mazda Tribute | i | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EF91-39-020
$8.76 MSRP: $38.66
You Save: $29.90 (78%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket No.2, Engine
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011, 2005-2006 Mazda Tribute | i | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EF92-39-080
$31.90 MSRP: $42.54
You Save: $10.64 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket No.4, Engine; Rear Bracket
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008, 2005-2006 Mazda Tribute | i, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EF95-39-020A
$8.76 MSRP: $51.04
You Save: $42.28 (83%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket No.2, Engine
- Replaces: EF95-39-020
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008, 2005-2006 Mazda Tribute | S | 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Front Mount Part Number: EC02-39-070B
$43.29 MSRP: $57.73
You Save: $14.44 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rubber No.4, Engine Mounting; Front Mount
- Position: Rear
- Replaces: EC02-39-070A, EC02-39-070
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX | 4 Cyl 2.0 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EC05-39-06XA
$10.13 MSRP: $59.05
You Save: $48.92 (83%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket No.3, Engine
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EC01-39-080C
$48.10 MSRP: $64.15
You Save: $16.05 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, No.4-Engine
- Replaces: EC01-39-080B, EC01-39-080A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Transmission Mount Part Number: EF92-39-070
$48.84 MSRP: $65.13
You Save: $16.29 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rubber No.4, Engine Mounting; Transmission Mount
- Position: Rear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011, 2005-2006 Mazda Tribute | i | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EF91-39-061B
$52.48 MSRP: $69.98
You Save: $17.50 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket No.3, Engine; Front Bracket
- Replaces: EF91-39-061, EF91-39-061A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008, 2005-2006 Mazda Tribute | i | 4 Cyl 2.3 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EF95-39-061A
$59.25 MSRP: $79.02
You Save: $19.77 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket No.3, Engine; Mount Bracket
- Position: Front
- Replaces: EF95-39-061
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011, 2005-2006 Mazda Tribute | S | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Mount Bracket Part Number: EF91-39-010
$59.28 MSRP: $79.05
You Save: $19.77 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket No.1, Engine; Mount Bracket
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011, 2005-2006 Mazda Tribute | i | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Tribute Side Mount Part Number: EF93-39-040
$61.56 MSRP: $82.10
You Save: $20.54 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rubber No.1, Engine Mounting; Side Mount
- Position: Rear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mazda Tribute | i | 4 Cyl 2.3 L GAS
View related parts
Mazda Tribute Transmission Mount Part Number: EF95-39-070
$49.20 MSRP: $65.62
You Save: $16.42 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rubber No.4, Engine Mounting; Front Mount, Transmission Mount
- Position: Rear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011, 2005-2006 Mazda Tribute | S | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Front Mount Part Number: EC01-39-070A
$78.80 MSRP: $105.09
You Save: $26.29 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rubber No.4, Engine Mounting; Rear Mount
- Position: Front
- Replaces: EC01-39-070
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Side Mount Part Number: EF92-39-040A
$77.91 MSRP: $103.90
You Save: $25.99 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rubber No.1, Engine Mounting; Side Mount
- Position: Rear
- Replaces: EF92-39-040
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011, 2005-2006 Mazda Tribute | i, S | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Side Mount Part Number: EF91-39-060C
$103.91 MSRP: $138.57
You Save: $34.66 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rubber No.3, Engine Mounting; Side Mount
- Position: Front
- Replaces: EF91-39-060, EF91-39-060B, EF91-39-060A
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011, 2005-2006 Mazda Tribute | i | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Tribute Side Mount Part Number: EF22-39-040
$103.51 MSRP: $138.04
You Save: $34.53 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rubber No.1, Engine Mounting; Rear Mount, Side Mount
- Replaces: ECY1-39-040, EC01-39-040A, EC01-39-040, EC11-39-040
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2001-2004 Mazda Tribute | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Tribute Side Mount Part Number: EF91-39-040
Product Specifications
- Other Name: Bracket No.2, Engine; Side Mount
- Position: Rear
- Warranty: This genuine part is guaranteed by Mazda's factory warranty.
Fits the following Vehicles:
- 2008-2011, 2005-2006 Mazda Tribute | i | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS

| Page 1 of 3 |Next >

1-20 of 52 Results

Mazda Tribute Engine Mount

The Mazda Tribute Engine Mount ensures the power plant of the compact SUV is securely fixed and prevents any vibration or noise from reaching the occupants, as is the case with the Mazda Tribute Engine Mount that shields comfort and the vital components of the drive system. The Engine Mounts are attached to the motor on one side and the chassis on the other, with a heavy rubber or fluid-filled bumper placed in between to keep the metals aligned, and the cushion absorbs the motion. The earlier models of the Mazda applied classic rubber-insulated mounts, which provided a stable firmness, whereas the later models featured hydraulic mounts or hydromounts in which the internal liquid absorbs finer tremors without causing the engine to become wayward. Some of the optimal trims came with electronically controlled active mounts that remained plush at idle speed to provide a more silky feel and hardened when the revs got high to throttle out any unwanted movement under hard acceleration on Mazda powerplants. Their primary differences revolve around the way each design varies in stiffness, with rubber types remaining the same, hydraulic styles being able to damp vibrations better, and active units changing dynamically through inbuilt valves. Rubber is prone to cracking due to heat, oil spillage, or plain old age, leaking hydraulic fluid or interference with electronic control, causing an Engine Mount to hang loose, tear, or tap against adjacent components. Individuals noticing new knocks or experiencing excessive vibration in a later Tribute must seek out detached metal plates, leaked liquid, or failed rubber, since replacing corrupted mounts will ensure their Mazda can be driven in a steady and safe fashion.

Looking for Engine Mount with proven quality? Choose OEM Engine Mount. Mazda designs and builds them to strict factory specs. Every piece goes through rigorous quality checks. You'll get parts that fit right and work like new. Shop our huge inventory of OEM Mazda Tribute parts. Enjoy the highly competitive prices online. Our site is your one-stop shop. Each genuine Tribute part includes a manufacturer's warranty. Buy with confidence. Our return policy is simple and hassle-free. In a rush? Choose expedited delivery at checkout. You'll love the streamlined experience from search to checkout to receiving your order.

Mazda Tribute Engine Mount Parts and Q&A

Side Mount
EF93-39-040
Q: How to remove the engine mount bracket and insulator on Mazda Tribute?
A:
This procedure is essentially the same as for the four-cylinder engine. Follow the outlined steps, removing the engine mount bracket bolts to separate the bracket from the engine and insulator, and then remove the engine mount insulator bolts to separate the insulator from the engine compartment.
Mount Bracket
EF95-39-020A
Q: Do engine mounts seldom require attention, and should broken or deteriorated mounts be replaced immediately to prevent damage or wear on driveline components on Mazda Tribute?
A:
Engine mounts do not need much time, but when they are broken or worn, they should be immediately changed to avoid damage and deterioration of the elements driving the engine. The engine should be lifted a little bit during the check in order to clear the mounts. Lift the vehicle up and rest it safely on jackstands, then place a jack under the engine Oil Pan with a large wood block between the jack head and the oil pan to avoid being damaged and take care not to lift up the engine to the point of removing all the weight on the mounts. Check the mounts, looking at them to identify cracks, hardened rubber, or separation of the material, rubber can crack along the lines. Test the relative motion between the mount plates and the engine or frame by a large screwdriver or pry bar; when motion is experienced, remove the engine and loosen the mount fasteners. Rubber preservative can be used to deteriorate. To replace, unscrew the battery cable on the negative terminal, and then lift the car and place it on jackstands unless it is already there. Lift the engine cover carefully so as to disconnect it with the ballstuds and remove it where it is present. Disassemble engine splash shield fasteners and disassemble splash shield underneath the vehicle, where fitted. With later models, the coolant reservoir can be unclipped, then moved aside without needing to disconnect the coolant lines. Position a floor jack beneath the engine with a block of wood in-between the jack head and oil pan to take the weight off the mounts. Unscrew the fasteners and remove the mount and frame and engine making sure that one of the mounts is not unscrewed unless the engine is removed. Installment is the opposite of removal where thread locking compound is applied on the mount bolts and tightened. Once the battery is reconnected, the Powertrain Control Module has to re-learn the idle and fuel trim strategy in order to provide optimal driving experience and performance.