Should Brake Calipers Be Replaced Instead of Overhauled When Fluid Leakage Is Indicated on Mazda 3?

In case of fluid leakage as indicated by replacement, it is advisable to replace the calipers and not to carry out overhaul as new and factory rebuilt units are on exchange basis hence making the work simpler. Never replace a caliper in singles, but in pairs. Removal The wheel lug nuts should be loosened, then the vehicle should be lifted and then set on jackstands, then its wheels removed. Unscrew the fitting of the brake hose, without removing it and loosen the caliper mounting bolts with a flare nut wrench to avoid damaging the fitting of the brake line. Reminiper the caliper off the mounting bracket, and unscrew it off the brake hose, without disconnecting the hose in case one is merely accessing other parts. In the case of the rear calipers, pull the parking brake cable out of the caliper by removing the brake cable out of the lever. To install: Reverse the process of removal and ensure the tightening of the mounting bolts to the required tightness. Make sure no hose connections leak and be very careful with checking brakes before inflating the vehicle back into normal operational condition. In case one of the rear calipers were taken off or changed, test and modify the parking brake where required.

How to properly remove and reinstall a brake caliper on Mazda RX-7?

Lift the front part of the car and place it on stands, and then take off the front wheel/s. It is simpler to loosen the flexible fluid line temporarily at the caliper and leave it temporarily loosened until the caliper has been removed. Unscrew four locking clips which hold the stopper plates to the caliper and remove two stopper plates. Then take the caliper off the rotor, and then completely disconnect the flexible hose, wipe the caliper off using rags or newspaper to catch any dripping fluid. Insert the end of the hose to avoid the entrance of dirt in the system and to avoid the continued leakage. In installation, a thin layer of lithium-based grease should be applied on all contact surfaces where the caliper is in contact with other metals. Install the flexible hose in a loose way and then simply tilt the caliper so that the top lip of the caliper is under the tension spring of the caliper bracket and with the anti-rattle spring in place. Installation Insert caliper under bottom tension spring and then lightly tap the plates at the stopper with a hammer or scratch or tap caliper on tension springs to clear. Insert the four lock-up clips into the stopper plates and screw the flexible fluid hose all the way. Install the wheel(s) again, bleed the brakes to all the air out of the system, drop the vehicle down to the ground, and check the brakes to make sure that they function correctly and show no leaks.

Genuine Mazda Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

200 Brake Calipers found

View related parts
Mazda Caliper Part Number: KAY0-26-71XA
$175.70 MSRP: $234.31
You Save: $58.61 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Body & Piston(Left), Caliper; Caliper Assembly
- Position: Driver Side
- Replaces: KAY0-26-71X
Fits the following Mazda Models:
- CX-5 | 2016-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: KAY0-26-61XA
$179.20 MSRP: $238.98
You Save: $59.78 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Body & Piston(Right), Caliper; Caliper Assembly
- Position: Passenger Side
- Replaces: KAY0-26-61X
Fits the following Mazda Models:
- CX-5 | 2016-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Assembly Part Number: VAY0-33-98Z
$155.73 MSRP: $207.68
You Save: $51.95 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Right), Padless-Front; Caliper
- Replaced by: VAY0-33-98ZA
Fits the following Mazda Models:
- CX-50 | 2023-2024 | 2.5 S, 2.5 Turbo | 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: K011-33-71X
$148.50 MSRP: $198.03
You Save: $49.53 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Body & Piston(Left), Caliper; Caliper Piston
- Position: Driver Side
Fits the following Mazda Models:
- CX-5 | 2013-2025 | 2.5 S, 2.5 S Carbon Edition, Carbon Edition, Grand Select, Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: BPYK-33-61XC
$267.91 MSRP: $357.29
You Save: $89.38 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Right), Padless-Front; Caliper Assembly
- Position: Passenger Side
- Replaces: BPYK-33-61XB, BPYK-33-61XA
Fits the following Mazda Models:
- 3 | 2006-2013 | Mazdaspeed, S, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
- 5 | 2012-2015, 2006-2010 | Grand Touring, Sport, Touring | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: GHY9-33-99Z
$276.36 MSRP: $368.56
You Save: $92.20 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Left), Padless-Front; Caliper Assembly
- Position: Driver Side
Fits the following Mazda Models:
- 6 | 2014-2021 | Grand Touring, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: NAYJ-26-98ZB
$317.50 MSRP: $423.42
You Save: $105.92 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Right), Padless-Rear; Caliper Assembly
- Position: Passenger Side
- Replaces: NAYJ-26-98ZA
Fits the following Mazda Models:
- MX-5 Miata | 2016-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Caliper Part Number: BDYS-26-61X
$343.66 MSRP: $458.31
You Save: $114.65 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Body & Piston(Right), Caliper; Caliper Assembly
- Position: Passenger Side
Fits the following Mazda Models:
- 3 | 2019-2025 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
- CX-30 | 2020-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: GMY0-26-71X
$352.34 MSRP: $469.88
You Save: $117.54 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Body & Piston(Left), Caliper; Caliper Assembly
- Position: Driver Side
Fits the following Mazda Models:
- 6 | 2016-2021 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: BCYA-26-71X
$393.32 MSRP: $528.75
You Save: $135.43 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Body & Piston(Left), Caliper; Caliper Assembly
- Position: Driver Side
Fits the following Mazda Models:
- 3 | 2019-2025 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Assembly Part Number: VAY0-33-99Z
$147.58 MSRP: $196.81
You Save: $49.23 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Left), Padless-Front; Caliper
- Replaced by: VAY0-33-99ZA
Fits the following Mazda Models:
- CX-50 | 2023-2024 | 2.5 S, 2.5 Turbo | 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: TKY8-33-99ZA
$260.23 MSRP: $347.04
You Save: $86.81 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Left), Padless-Front; Caliper Assembly
- Position: Driver Side
- Replaces: TKY8-33-99Z
Fits the following Mazda Models:
- CX-5 | 2019-2025 | 2.5 Carbon Turbo, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition Turbo, Grand Touring Reserve, Signature | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
- CX-9 | 2016-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: K0Y1-33-98Z
$268.49 MSRP: $358.06
You Save: $89.57 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Right), Padless-Front; Caliper Assembly
- Position: Passenger Side
Fits the following Mazda Models:
- CX-5 | 2013-2025 | 2.5 S, 2.5 S Carbon Edition, Carbon Edition, Grand Select, Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: NAYF-33-98Z
$636.30 MSRP: $869.44
You Save: $233.14 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Right), Padless-Front; Caliper Assembly
- Position: Passenger Side
Fits the following Mazda Models:
- MX-5 Miata | 2016-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Caliper Part Number: DGY9-33-99Z
$196.84 MSRP: $262.50
You Save: $65.66 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Left), Padless-Front; Caliper Assembly
- Position: Driver Side
Fits the following Mazda Models:
- CX-30 | 2020-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: K0Y1-26-99ZA
$322.15 MSRP: $429.62
You Save: $107.47 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Left), Padless-Rear; Caliper Assembly
- Position: Driver Side
- Replaces: K0Y1-26-99Z
Fits the following Mazda Models:
- CX-5 | 2013-2015 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: K0Y1-26-98ZA
$322.15 MSRP: $429.62
You Save: $107.47 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Right), Padless-Rear; Caliper Assembly
- Position: Passenger Side
- Replaces: K0Y1-26-98Z
Fits the following Mazda Models:
- CX-5 | 2013-2015 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: BPYK-33-71XC
$285.29 MSRP: $380.46
You Save: $95.17 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper(Left), Padless-Front; Caliper Assembly
- Position: Driver Side
- Replaces: BPYK-33-71XB, BPYK-33-71XA
Fits the following Mazda Models:
- 3 | 2006-2013 | Mazdaspeed, S, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
- 5 | 2012-2015, 2006-2010 | Grand Touring, Sport, Touring | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Caliper Part Number: BPYK-26-61XB
$316.85 MSRP: $422.55
You Save: $105.70 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Right, Padless Rear
- Position: Passenger Side
- Replaces: BPYK-26-61X, BPYK-26-61XA
Fits the following Mazda Models:
- 3 | 2004-2009 | Mazdaspeed, S, SP23, i | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Mazda Caliper(Left), Padless-Front Part Number: KMY7-33-99Z
$439.89 MSRP: $591.37
You Save: $151.48 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CALIPER(L),PADLESS-FR; Caliper, Caliper Assembly
- Position: Driver Side
Fits the following Mazda Models:
- CX-70 | 2025 | PHEV, Turbo, Turbo S | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)
- CX-90 | 2024-2025 | PHEV, Turbo, Turbo S | 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.3 L MILD HYBRID EV-GAS (MHEV)

| Page 1 of 10 |Next >

1-20 of 200 Results

Mazda Brake Caliper

Mazda Brake Caliper provides accurate clamping force that converts pedal pressure into immediate, confident stops, providing drivers with control in every situation. Mazda dates its story back to 1931 and gained fame with the spirited rotary engine, then began tweaking efficiency with Skyactiv powertrains that sip fuel but don't lose performance. Its Kodo design features additional sculpted lines that appear ready to leap forward even in a park setting, while i-Activsense features such as lane keeping and radar cruise keep an eye on the road to help protect passengers. Mazda also explores electric drive and mild hybrids and proves i-Activ AWD on rough terrain, all to maintain the fun to drive character fans celebrate. Within every Mazda vehicle, to keep up with this dynamic spirit, every Brake Caliper in the lineup transforms hydraulic energy into reliable stopping power. A fixed type uses the pistons on both sides of the rotor for balanced bite and a firm pedal, whereas the lighter floating style slides over guide pins to pinch the disc from one side and cut mass without loss of effectiveness. Robust cast iron bodies, steel or phenolic pistons, and protective seals resist heat and corrosion so the Brake Caliper keeps pads gripping smoothly mile after mile. Regular checks help ensure Mazda braking hardware continues to perform with the same confidence as the engines that propel it.

You'll get great performance and real durability when you pick genuine OEM Brake Caliper. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Brake Caliper Parts and Q&A

Caliper
BPYK-26-61XB
Q: Should Brake Calipers Be Replaced Instead of Overhauled When Fluid Leakage Is Indicated on Mazda 3?
A:
In case of fluid leakage as indicated by replacement, it is advisable to replace the calipers and not to carry out overhaul as new and factory rebuilt units are on exchange basis hence making the work simpler. Never replace a caliper in singles, but in pairs. Removal The wheel lug nuts should be loosened, then the vehicle should be lifted and then set on jackstands, then its wheels removed. Unscrew the fitting of the brake hose, without removing it and loosen the caliper mounting bolts with a flare nut wrench to avoid damaging the fitting of the brake line. Reminiper the caliper off the mounting bracket, and unscrew it off the brake hose, without disconnecting the hose in case one is merely accessing other parts. In the case of the rear calipers, pull the parking brake cable out of the caliper by removing the brake cable out of the lever. To install: Reverse the process of removal and ensure the tightening of the mounting bolts to the required tightness. Make sure no hose connections leak and be very careful with checking brakes before inflating the vehicle back into normal operational condition. In case one of the rear calipers were taken off or changed, test and modify the parking brake where required.
Caliper
FD13-33-980D
Q: How to properly remove and reinstall a brake caliper on Mazda RX-7?
A:
Lift the front part of the car and place it on stands, and then take off the front wheel/s. It is simpler to loosen the flexible fluid line temporarily at the caliper and leave it temporarily loosened until the caliper has been removed. Unscrew four locking clips which hold the stopper plates to the caliper and remove two stopper plates. Then take the caliper off the rotor, and then completely disconnect the flexible hose, wipe the caliper off using rags or newspaper to catch any dripping fluid. Insert the end of the hose to avoid the entrance of dirt in the system and to avoid the continued leakage. In installation, a thin layer of lithium-based grease should be applied on all contact surfaces where the caliper is in contact with other metals. Install the flexible hose in a loose way and then simply tilt the caliper so that the top lip of the caliper is under the tension spring of the caliper bracket and with the anti-rattle spring in place. Installation Insert caliper under bottom tension spring and then lightly tap the plates at the stopper with a hammer or scratch or tap caliper on tension springs to clear. Insert the four lock-up clips into the stopper plates and screw the flexible fluid hose all the way. Install the wheel(s) again, bleed the brakes to all the air out of the system, drop the vehicle down to the ground, and check the brakes to make sure that they function correctly and show no leaks.