How to check and replace the Cooling Fan Assembly and Cooling Fan Clutch on Mazda MPV?

Checking the fan To test the fan, first unscrew the negative battery cable and shake the fans back and forth manually to test the bearing play. Turn the blades by hand when cold, it must turn freely. Checks: Check the clutch assembly, check the bi-metal spring to determine whether it is deformed or not, and check whether there is a lot of fluid leakage, and also examine whether there is leakage of grease on the exit, and replace the fan clutch accordingly. The ignition should be switched off, and the negative battery cable should be disconnected once more, when the engine is warmed up. Rotate fan manually; it must have some resistance and in case it is easy to rotate the fan then the fan clutch has to be replaced. To remove, disassemble the negative battery cable, unbolt and remove the fresh air duct on the radiator top and remove the nuts which hold the fan assembly to the water pump flange. Take out the top mounting bolts of the fan shroud and squeeze the plastic bottom fasteners on the lower parts of the fan shroud with the long needle-nose pliers. A cooling fan assembly may then be installed using a movement of both the shroud and fan upwards. Removal is done in the opposite sequence of installation.

How to remove and reassemble the Cooling Fan Clutch attached to the water pump pulley on Mazda RX-7?

The fan assembly is fitted to the water pump pulley on the front side of the engine. Starting with the four bolts that hold the fan assembly to the flange on the water pump pulley; remove the assembly out of the radiator cowling and the engine compartment. In case this is too troublesome, remove the cowling on the sides of the radiator and raise it a bit so that it clears. The next step is to loosen up the four bolts connecting the fan with the drive clutch and take apart the two parts. To reassemble, attach the fan drive to the fan and attach the assembly to the flange on the water pump pulley.

Genuine Mazda Cooling Fan Clutch

Fan Clutch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 Cooling Fan Clutches found

View related parts
Mazda Clutch Part Number: 1F82-15-150
$222.80 MSRP: $297.13
You Save: $74.33 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fan Drive; Clutch
- Replaces: ZZP2-15-150
Fits the following Mazda Models:
- B4000 | 1998-2009 | Base, DS, SE, Troy Lee | 6 Cyl 4.0 L GAS
View related parts
Mazda Clutch Part Number: G607-15-150A
$278.83 MSRP: $371.84
You Save: $93.01 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fan Drive; Clutch
- Replaces: G607-15-150
Fits the following Mazda Models:
- B2600 | 1989-1993 | Base, LE-5, LX, SE-5 | 4 Cyl 2.6 L GAS
View related parts
Mazda Clutch Part Number: N350-15-150
$367.63 MSRP: $490.27
You Save: $122.64 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- RX-7 | 1989-1991 | Base, Convertible, GTU, GTUs, GXL, GXL 2+2, Turbo | 2 Cyl 1.3 L GAS
View related parts
Mazda Clutch Part Number: 1F80-15-150
Product Specifications
- Other Name: Fan Drive; Clutch
- Replaces: 1F20-15-150, 1F20-15-150A, 1F70-15-150, 1F70-15-150A
Fits the following Mazda Models:
- B2300 | 2001-2009 | Base, SE, SX | 4 Cyl 2.3 L GAS
View related parts
Mazda Clutch Part Number: 1F81-15-150
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- B3000 | 1998-2007 | Base, DS, SE, SX, Troy Lee | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mazda Clutch Part Number: AM15159X3
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- B2600 | 1987-1988 | Base, LX, SE-5 | 4 Cyl 2.6 L GAS
View related parts
Mazda Clutch Part Number: FE2H-15-150B
Product Specifications
- Other Name: Fan Drive; Fan Clutch
Fits the following Mazda Models:
- B2000 | 1987 | Base, LX, SE-5 | 4 Cyl 2.0 L GAS
- B2200 | 1987-1993 | Base, LE-5, LX, SE-5 | 4 Cyl 2.2 L GAS
- B2600 | 1987-1993 | Base, LE-5, LX, SE-5 | 4 Cyl 2.6 L GAS
View More
View related parts
Mazda Clutch Part Number: FE66-23-907
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- B2000 | 1986 | Base, LX, SE-5 | 4 Cyl 2.0 L GAS
- B2200 | 1987-1993 | Base, LE-5, LX, SE-5 | 4 Cyl 2.2 L GAS
View related parts
Mazda Clutch Part Number: JE2315150
Product Specifications
- Other Name: Fan Drive
Fits the following Mazda Models:
- MPV | 1989-1990 | Passenger | 6 Cyl 3.0 L GAS
View related parts
Mazda Clutch Part Number: JE48-15-150C
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- 929 | 1992-1995 | Base | 6 Cyl 3.0 L GAS
- MPV | 1996-1998 | DX, ES, LX | 6 Cyl 3.0 L GAS
View related parts
Mazda Clutch Part Number: JE57-15-150A
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- MPV | 1992-1995 | L, LX, LXE, Passenger | 6 Cyl 3.0 L GAS
View related parts
Mazda Clutch Part Number: JF0415150A
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- 929 | 1988-1991 | Base, S | 6 Cyl 3.0 L GAS
View related parts
Mazda Clutch Part Number: N249-15-210B
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- RX-7 | 1984-1985 | GS, GSL, S | 2 Cyl 1.1 L GAS
View related parts
Mazda Clutch Part Number: ZZL315150B
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- Navajo | 1991-1992 | DX, LX | 6 Cyl 4.0 L GAS
View related parts
Mazda Clutch Part Number: ZZM2-15-150B
Product Specifications
- Other Name: Fan Drive; Clutch, Fan Clutch
Fits the following Mazda Models:
- B4000 | 1994-1997 | Base, LE, SE | 6 Cyl 4.0 L GAS
View related parts
Mazda Clutch Part Number: ZZM7-15-150
Product Specifications
- Other Name: Fan Drive
Fits the following Mazda Models:
- B3000 | 1994 | Base, SE | 6 Cyl 3.0 L GAS
View related parts
Mazda Clutch Part Number: ZZMA15150
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- B3000 | 1994-1996 | Base, SE | 6 Cyl 3.0 L GAS
- B4000 | 1995-1997 | Base, LE, SE | 6 Cyl 4.0 L GAS
View related parts
Mazda Clutch Part Number: ZZP0-15-150
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- B2500 | 1998-2001 | SE, SX, Troy Lee | 4 Cyl 2.5 L GAS
View related parts
Mazda Clutch Part Number: ZZP3-15-150
Product Specifications
- Other Name: Fan Drive; Clutch
Fits the following Mazda Models:
- B2500 | 1998-2001 | SE, SX, Troy Lee | 4 Cyl 2.5 L GAS

Mazda Cooling Fan Clutch

The Mazda Cooling Fan Clutch helps keep engine heat in check and reduces fuel consumption in the entire Mazda range, providing drivers with a quieter driving experience and reliable readings. Mazda cars get awards for fun driving, Kodo styling that looks eager even at rest, and Skyactiv engines that sip fuel without dulling acceleration. Advanced i-Activsense safety helps to watch blind spots, while available i-Activ AWD digs in on rough roads, so Mazda vehicles feel confident and fun whether you're commuting or exploring. Hybrid and electric efforts demonstrate Mazda's commitment to cleaner motion, and both cabins strike a balance of intuitive tech and materials that feel a class above, keeping a heritage of starting with rotary innovation and continuing to support driver engagement. At the center of this dependability is the Cooling Fan Clutch, which has a thermostatic core and viscous fluid in it, engaging the radiator fan only when the airflow through the grille is insufficient to avoid overheating when the vehicle is in slow traffic, but allowing the fan blades to run without resistance at highway speed. By spinning the fan only when the heat rises, this clutch also has the effect of reducing drag on the crankshaft, which protects belts, prolongs the life of the water pump, and slightly increases mileage. Because of this self-regulating design that is compatible with standard fan assemblies, the Cooling Fan Clutch is a universal solution that is compatible with the entire Mazda lineup to ensure consistent thermal control without additional complexity.

You'll get great performance and real durability when you pick genuine OEM Cooling Fan Clutch. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Cooling Fan Clutch Parts and Q&A

Clutch
JE48-15-150C
Q: How to check and replace the Cooling Fan Assembly and Cooling Fan Clutch on Mazda MPV?
A:
Checking the fan To test the fan, first unscrew the negative battery cable and shake the fans back and forth manually to test the bearing play. Turn the blades by hand when cold, it must turn freely. Checks: Check the clutch assembly, check the bi-metal spring to determine whether it is deformed or not, and check whether there is a lot of fluid leakage, and also examine whether there is leakage of grease on the exit, and replace the fan clutch accordingly. The ignition should be switched off, and the negative battery cable should be disconnected once more, when the engine is warmed up. Rotate fan manually; it must have some resistance and in case it is easy to rotate the fan then the fan clutch has to be replaced. To remove, disassemble the negative battery cable, unbolt and remove the fresh air duct on the radiator top and remove the nuts which hold the fan assembly to the water pump flange. Take out the top mounting bolts of the fan shroud and squeeze the plastic bottom fasteners on the lower parts of the fan shroud with the long needle-nose pliers. A cooling fan assembly may then be installed using a movement of both the shroud and fan upwards. Removal is done in the opposite sequence of installation.
Clutch
N249-15-210B
Q: How to remove and reassemble the Cooling Fan Clutch attached to the water pump pulley on Mazda RX-7?
A:
The fan assembly is fitted to the water pump pulley on the front side of the engine. Starting with the four bolts that hold the fan assembly to the flange on the water pump pulley; remove the assembly out of the radiator cowling and the engine compartment. In case this is too troublesome, remove the cowling on the sides of the radiator and raise it a bit so that it clears. The next step is to loosen up the four bolts connecting the fan with the drive clutch and take apart the two parts. To reassemble, attach the fan drive to the fan and attach the assembly to the flange on the water pump pulley.