How to replace the hood latch and hood release cable on Mazda 3?

In order to replace the hood latch the first step is to unscrew the cable of the negative battery terminal, and in 2010 and later models the hood latch switch connector. Draw a line around the latch to line up and then remove the retaining bolts that hold the latch to the radiator support and remove the latch. Be careful the airbag front crash sensor is attached using the same mounting bolt as the hood latch, do not hit or drop the sensor to avoid damaging the sensor and will deploy the airbag. The next step is to raise the cable out of the bracket and out of the latch assembly to disconnect the cable end plug. In case of the release cable, the upper engine cover is removed by pushing it off the mounting posts by its two sides. Next, loosen the battery air inlet fasteners, air inlet, battery and battery tray. Unclips: Disconnect the release cable of the hood latch and remove the release cable clips off the fender and the wiring harness. To release the locking tab, pull the release handle down (you have to hold a small screwdriver to press the tab down) and then, now that the locking tab is released, pull the handle up and out of the instrument panel and then unscrew the release cable off the release handle and pull it through the firewall. Removal is the opposite of the installation process.

How to remove the hood latch and hood release cable on Mazda 6?

The first step to the removal of the hood latch is firstly to detach the cable to the negative battery terminal. Mark a line on the latch to match up when fitting, remove the retaining bolts attaching the hood latch to the radiator support and remove the latch. Be careful to ensure that the front airbag crash sensor is attached with the hood latch mounting bolt so as not to hit or drop the sensor and therefore not to cause damage to the sensor or activate the airbag. Secondly, pull the cable out of the bracket to release the cable out of the latch assembly and pull the cable end plug out of the latch. In the case of the release cable, in the engine compartment, loosen the hoodlatch and separate the hood release cable with the hoodlatch. Next, take out the front bumper cover and the headlight housing. Unscrew the lug nuts of the wheel, place the vehicle safely on jackstands and take away the left front wheel and the inner fender splash shield. Unscrew the release cable clips of fender and wiring harness. Within the car, press the pull lever along with a small screwdriver to press the locking tab down. Using the tab, push the handle up and out of the instrument panel, snap the release cable out of the handle and push it through the firewall. The opposite of removal is installation.

Genuine Mazda Hood Release Cable

Hood Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

57 Hood Release Cables found

View related parts
Mazda Release Cable Part Number: BHN9-56-720B
$23.51 MSRP: $31.36
You Save: $7.85 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
- Replaces: BHN9-56-720A, BHN9-56-720
Fits the following Mazda Models:
- 3 | 2014-2018 | Grand Touring, i Grand Touring, I Sport, i SV, I Touring, s Grand Touring, s Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: K070-56-720B
$25.43 MSRP: $33.91
You Save: $8.48 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
- Replaces: KD53-56-720, K070-56-720A
Fits the following Mazda Models:
- CX-5 | 2013-2016 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: KB7W-56-720A
$25.49 MSRP: $34.00
You Save: $8.51 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release Hood; Release Cable
- Replaces: KB7W-56-720
Fits the following Mazda Models:
- CX-5 | 2017-2024 | 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: BBM4-56-720-00
$25.91 MSRP: $34.56
You Save: $8.65 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
Fits the following Mazda Models:
- 3 | 2010-2013 | i, Mazdaspeed, S | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: NA1J-56-720A
$31.74 MSRP: $42.32
You Save: $10.58 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
- Replaces: NA1J-56-720
Fits the following Mazda Models:
- MX-5 Miata | 2016-2023 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Release Cable Part Number: GHP9-56-720A
$32.45 MSRP: $43.28
You Save: $10.83 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
- Replaces: GHP9-56-720
Fits the following Mazda Models:
- 6 | 2014-2021 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: BCJH-56-720A
$35.59 MSRP: $47.46
You Save: $11.87 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet; Release Cable
Fits the following Mazda Models:
- 3 | 2019-2024 | 2.0, 2.5 Carbon Turbo, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select, Select Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: TK48-56-720B
$36.98 MSRP: $49.31
You Save: $12.33 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release Hood; Release Cable
- Replaces: TK48-56-720A
Fits the following Mazda Models:
- CX-9 | 2016-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: DFR5-56-720
$37.56 MSRP: $50.10
You Save: $12.54 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet; Release Cable
Fits the following Mazda Models:
- CX-30 | 2020-2023 | 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: NP32-56-720
$37.95 MSRP: $50.60
You Save: $12.65 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet; Release Cable
Fits the following Mazda Models:
- MX-5 Miata | 2013-2015 | 25th Anniversary Edition, Club, Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Release Cable Part Number: CG15-56-720
$38.11 MSRP: $50.82
You Save: $12.71 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
Fits the following Mazda Models:
- 5 | 2012-2015 | Grand Touring, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: NP41-56-720
$36.19 MSRP: $48.25
You Save: $12.06 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet; Release Cable
Fits the following Mazda Models:
- MX-5 Miata | 2013-2015 | 25th Anniversary Edition, Club, Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Release Cable Part Number: GD7A-56-720
$39.51 MSRP: $52.69
You Save: $13.18 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
Fits the following Mazda Models:
- 626 | 1998-2002 | DX, ES, LX | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Mazda Release Cable Part Number: B25D-56-720
$39.54 MSRP: $52.73
You Save: $13.19 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
Fits the following Mazda Models:
- Protege | 1999-2003 | DX, ES, LX, Mazdaspeed, MP3 | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Protege5 | 2002-2003 | Base | 4 Cyl 2.0 L GAS
View related parts
Mazda Release Cable Part Number: NE51-56-720
$42.65 MSRP: $56.87
You Save: $14.22 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, Special Edition, Sport, SV, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Release Cable Part Number: DF71-56-720
$42.79 MSRP: $57.05
You Save: $14.26 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
Fits the following Mazda Models:
- 2 | 2011-2014 | Sport, Touring | 4 Cyl 1.5 L GAS
View related parts
Mazda Release Cable Part Number: LC62-56-720C
$41.50 MSRP: $55.34
You Save: $13.84 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
- Replaces: LC62-56-720B, LC62-56-720A
Fits the following Mazda Models:
- MPV | 2000-2006 | DX, ES, LX, LX-SV | 6 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Release Cable Part Number: FF14-56-720
$40.58 MSRP: $54.11
You Save: $13.53 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
Fits the following Mazda Models:
- RX-8 | 2009-2011 | Grand Touring, R3, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Release Cable Part Number: NE61-56-720
$44.05 MSRP: $58.74
You Save: $14.69 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, Special Edition, Sport, SV, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Release Cable Part Number: TD11-56-720A-00
$44.34 MSRP: $59.13
You Save: $14.79 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire, Release-Bonnet
Fits the following Mazda Models:
- CX-9 | 2007-2015 | Grand Touring, Sport, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS

| Page 1 of 3 |Next >

1-20 of 57 Results

Mazda Hood Release Cable

The Mazda Hood Release Cable allows drivers to pop the hood in one fluid movement without compromising the latch while driving. Mazda receives worldwide acclaim for its vivacious handling, fuel-efficient Skyactiv power units, and the Kodo design that makes every curve appear ready to sprint. The brand combines responsive steering with i-Activsense safety tools that monitor blind spots and provide guidance for distance control, while its expanding roster of hybrids indicates that Mazda is looking to make your commute greener without ever taking the fun out. All-wheel drive models are tested on rough tracks to ensure owners can trust their cars on rainy or snowy days, and the company has a long history beginning in 1931, highlighted by the iconic rotary, which suggests Mazda knows how to innovate and delight. Just as those bold technologies ensure protection of performance, the Hood Release Cable ensures quick access to the engine bay. Built from strong steel strands that are sheathed from the weather, each Hood Release Cable connects the cabin lever to several latch points so a single pull releases both sides at once and prevents uneven stress. Over years of heat, cold, and vibration, normal cables can corrode or stretch, but this well-routed replacement puts light, confident pulls in the hands of owners to check oil, coolant, or belts before little problems become costly. Simple, reliable, and vital, it is the silent partner of the spirited character that defines Mazda.

You'll get great performance and real durability when you pick genuine OEM Hood Release Cable. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Hood Release Cable Parts and Q&A

Release Cable
BP4K-56-720C
Q: How to replace the hood latch and hood release cable on Mazda 3?
A:
In order to replace the hood latch the first step is to unscrew the cable of the negative battery terminal, and in 2010 and later models the hood latch switch connector. Draw a line around the latch to line up and then remove the retaining bolts that hold the latch to the radiator support and remove the latch. Be careful the airbag front crash sensor is attached using the same mounting bolt as the hood latch, do not hit or drop the sensor to avoid damaging the sensor and will deploy the airbag. The next step is to raise the cable out of the bracket and out of the latch assembly to disconnect the cable end plug. In case of the release cable, the upper engine cover is removed by pushing it off the mounting posts by its two sides. Next, loosen the battery air inlet fasteners, air inlet, battery and battery tray. Unclips: Disconnect the release cable of the hood latch and remove the release cable clips off the fender and the wiring harness. To release the locking tab, pull the release handle down (you have to hold a small screwdriver to press the tab down) and then, now that the locking tab is released, pull the handle up and out of the instrument panel and then unscrew the release cable off the release handle and pull it through the firewall. Removal is the opposite of the installation process.
Release Cable
GJ6A-56-720G
Q: How to remove the hood latch and hood release cable on Mazda 6?
A:
The first step to the removal of the hood latch is firstly to detach the cable to the negative battery terminal. Mark a line on the latch to match up when fitting, remove the retaining bolts attaching the hood latch to the radiator support and remove the latch. Be careful to ensure that the front airbag crash sensor is attached with the hood latch mounting bolt so as not to hit or drop the sensor and therefore not to cause damage to the sensor or activate the airbag. Secondly, pull the cable out of the bracket to release the cable out of the latch assembly and pull the cable end plug out of the latch. In the case of the release cable, in the engine compartment, loosen the hoodlatch and separate the hood release cable with the hoodlatch. Next, take out the front bumper cover and the headlight housing. Unscrew the lug nuts of the wheel, place the vehicle safely on jackstands and take away the left front wheel and the inner fender splash shield. Unscrew the release cable clips of fender and wiring harness. Within the car, press the pull lever along with a small screwdriver to press the locking tab down. Using the tab, push the handle up and out of the instrument panel, snap the release cable out of the handle and push it through the firewall. The opposite of removal is installation.