How to remove and install the front bumper on Mazda B2000?

To install or remove the bumper of models between 1971 and 1984, the bumper should be supported then extract the bolts attaching the bumper bracket to the frame and the bolts that attach the bumper to the bracket and reverse the process to install back. To remove the combination lamps in the grille and then remove the actual grille of the model between the years 1986 and 1969. This is then followed by unplugging the wiring in the lamps that are installed on the bumper skirt and the removal of the bumper skirt and end pieces. Once holding the bumper, unscrew the bolts that hold the bumper bracket to the frame and then to the bumper followed by re-screwing back after the order in the reverse order of the actions.

How to remove and install the rear bumper and shock absorber on Mazda RX-7?

Open the rear glass hatch and peel back the floor covering at the rear of the luggage compartment. On each side of the floor, there are service holes covered by plates; remove the two securing screws and lift off the covers. Access the lock nut and jam nut of the shock absorber piston inside the service holes. Raise the rear end of the vehicle and support it firmly with stands for the remaining procedures. Under the bottom lip of the bumper, locate the shock absorber mounting brackets and attaching nuts, marking around these brackets on the body panel. Remove the four nuts (two on each side bracket) while supporting the bumper assembly, then lift the bumper assembly away from the car. Inspect the shock absorber and measure the length of the spring, which should be approximately 2.50 in (64 mm); if not, replace the shock absorber with a new one. To install the rear bumper, lift it into position and loosely install the four securing nuts. Adjust the bumper to align with the identification marks made during disassembly, then tighten the four nuts. Tighten the lock nuts and jam nuts inside the vehicle and install the access hole covers, followed by placing the floor covering back in its original position.

Genuine Mazda Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

Filter by Part Type

Bumper Cover
Other Bumpers

Filter by Part Type

408 Bumpers found

View related parts
Mazda Bumper Cover Part Number: NDYN-50-22X-BB
$400.35 MSRP: $538.20
You Save: $137.85 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Rear
Fits the following Mazda Models:
- MX-5 Miata | 2019 | Club, Grand Touring, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Bumper Cover Part Number: KBYB-50-22XB-BB
$283.89 MSRP: $378.59
You Save: $94.70 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Rear
- Replaces: KNYL-50-22X-BB, KBYB-50-22X-BB
Fits the following Mazda Models:
- CX-5 | 2019-2021 | Carbon Edition, Carbon Edition Turbo, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda Bumper Cover Part Number: BJS7-50-031A-9U
$378.16 MSRP: $508.39
You Save: $130.23 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Front
- Replaces: BJS7-50-031A-BB, BHN1-50-031A-BB, BHN1-50-031B-BB, BJS7-50-031-BB
Fits the following Mazda Models:
- 3 | 2014-2016 | I Sport, I Touring, i Grand Touring, i SV, s Grand Touring, s Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Bumper Cover Part Number: DGY9-50-220
$420.26 MSRP: $564.99
You Save: $144.73 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Rear
- Replaces: DGH9-50-221-BB
Fits the following Mazda Models:
- CX-30 | 2020-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Bumper, Front Part Number: GMY3-50-031
$454.61 MSRP: $611.16
You Save: $156.55 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: BUMPER,FRONT; Bumper Cover
- Position: Front
- Replaces: GMN3-50-031C-BB, GMN3-50-031B-BB
Fits the following Mazda Models:
- 6 | 2016-2017 | Grand Touring, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda Bumper Cover Part Number: KLYF-50-22X-9U
$273.94 MSRP: $365.32
You Save: $91.38 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rear Bumper W/O Parking S
- Replaces: KBYA-50-22XB-BB, KBYA-50-22X-BB, KLYF-50-22X-BB
Fits the following Mazda Models:
- CX-5 | 2017-2021 | Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda Bumper Cover Part Number: KSD4-50-221B-9U
$301.99 MSRP: $402.73
You Save: $100.74 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Rear
- Replaces: KSD4-50-221B, KSD4-50-221B-BB, KSC2-50-221A-BB
Fits the following Mazda Models:
- CX-5 | 2022-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature | 4 Cyl 2.5 L GAS
View related parts
Mazda Bumper Cover Part Number: NFYR-50-22X-BB
$498.52 MSRP: $670.19
You Save: $171.67 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Rear
Fits the following Mazda Models:
- MX-5 Miata | 2020-2023 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Bumper Cover Part Number: N0Y1-50-030A-BB
$445.98 MSRP: $599.55
You Save: $153.57 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Front
- Replaces: N0Y1-50-030A, NE46-50-031A, N0Y1-50-031A, N0Y1-50-031
Fits the following Mazda Models:
- Miata | 2001-2005 | Base, LS, Mazdaspeed, SE, Shinsen | 4 Cyl 1.8 L GAS
View related parts
Mazda Bumper, Front Part Number: N2Y1-50-03XA-BB
$615.46 MSRP: $827.41
You Save: $211.95 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: BUMPER,FRONT; Bumper Cover
- Position: Front
- Replaces: N2Y1-50-03X-BB, NAY4-50-03X-BB, N2Y1-50-03XA-8P
Fits the following Mazda Models:
- MX-5 Miata | 2016-2025 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Absorber Part Number: TD11-50-111D
$128.40 MSRP: $171.23
You Save: $42.83 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Foam, Bumper-Front; Energy Absorber
- Replaces: TD11-50-111B, TD11-50-111C
Fits the following Mazda Models:
- CX-9 | 2007-2015 | Grand Touring, Sport, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda BUMPER, FRONT (W/O PRIMER) Part Number: KD45-50-031-9U
$311.83 MSRP: $415.84
You Save: $104.01 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Cover
- Position: Front
- Replaces: KD45-50-031-BB, KD45-50-031
Fits the following Mazda Models:
- CX-5 | 2013-2016 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Bumper Cover Part Number: KSD5-50-031A-BB
$333.65 MSRP: $444.95
You Save: $111.30 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Front
- Replaces: KSC3-50-031-BB, KSD5-50-031-BB
Fits the following Mazda Models:
- CX-5 | 2022-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature | 4 Cyl 2.5 L GAS
View related parts
Mazda Impact Bar Part Number: TD11-50-070B
$426.70 MSRP: $573.63
You Save: $146.93 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Reinforcement, Front Bumper
Fits the following Mazda Models:
- CX-9 | 2007-2015 | Grand Touring, Sport, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Mazda Lower Cover Part Number: BCW8-50-101A
$15.98 MSRP: $21.30
You Save: $5.32 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover(Right), Front Bumper
- Position: Passenger Side
- Replaces: BCW8-50-101
Fits the following Mazda Models:
- 3 | 2010 | i | 4 Cyl 2.0 L GAS
View related parts
Mazda Bumper Cover Part Number: KL2F-50-031-BB
$311.83 MSRP: $415.84
You Save: $104.01 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Front
- Replaced by: KL2F-50-031-9U
Fits the following Mazda Models:
- CX-5 | 2017-2021 | Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
View related parts
Mazda Bumper Cover Part Number: VA40-50-031B-BB
$307.49 MSRP: $410.06
You Save: $102.57 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Front
- Replaces: VA40-50-031-BB, VA40-50-031A-BB
Fits the following Mazda Models:
- CX-50 | 2023-2025 | 2.5 S, 2.5 Turbo, Hybrid Preferred, Hybrid Premium | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS
View related parts
Mazda Lower Cover Part Number: KSD7-50-222-BB
$319.06 MSRP: $425.51
You Save: $106.45 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Rear Lower
- Position: Lower
Fits the following Mazda Models:
- CX-5 | 2022-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature | 4 Cyl 2.5 L GAS
View related parts
Mazda Impact Bar Part Number: KPF1-50-070A
$352.58 MSRP: $470.20
You Save: $117.62 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Reinforcement, Front Bumper
- Replaces: KPF1-50-070
Fits the following Mazda Models:
- CX-5 | 2022-2025 | 2.5 Carbon Turbo, 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature | 4 Cyl 2.5 L GAS
View related parts
Mazda Bumper Cover Part Number: TK22-50-221B-BB
$542.20 MSRP: $728.91
You Save: $186.71 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper, Rear
- Replaces: TK22-50-221-BB
Fits the following Mazda Models:
- CX-9 | 2013-2015 | Grand Touring, Sport, Touring | 6 Cyl 3.7 L GAS

| Page 1 of 21 |Next >

1-20 of 408 Results

Mazda Bumper

Mazda Bumper serves as a strong first line of defense, absorbing low-speed impacts and protecting expensive components behind it. Mazda is a company that has gained respect throughout the world since 1931 for cars that combine spirited handling with smart efficiency, with Mazda rotary power in the past and Skyactiv engineering today. Its Kodo design captures motion when it is parked, while i-Activsense technologies like radar cruise and lane keep provide confidence on any commute. Adventurous drivers love the i-Activ AWD that handles rough trails, and the brand is now looking at electric and mild hybrid options to combine the fun of driving with cleaner travel. All these advances demonstrate how Mazda continues to strive for the balance of emotion and reason. The Bumper is no exception to this philosophy and incorporates form and function throughout the range. A modern Bumper is flush with the body, relying on a plastic cover, an inner beam, and energy-absorbing foam to shield the body from the daily bumps to keep sheet metal, lamps, and cooling parts safe. Because mounting points remain constant, replacement of a damaged unit is still easy and factory fit and paint harmony is maintained. Owners can choose color-matched finishes or subtle black trims, getting style without sacrificing protection. By safeguarding key elements and preserving sleek lines, the Mazda Bumper upholds the brand's promise of reliability, affordability, and lasting pride.

You'll get great performance and real durability when you pick genuine OEM Bumper. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Bumper Parts and Q&A

Bumper Assembly
8BU1-50-200
Q:
How to remove and install the front bumper on Mazda B2000?
A:
To install or remove the bumper of models between 1971 and 1984, the bumper should be supported then extract the bolts attaching the bumper bracket to the frame and the bolts that attach the bumper to the bracket and reverse the process to install back. To remove the combination lamps in the grille and then remove the actual grille of the model between the years 1986 and 1969. This is then followed by unplugging the wiring in the lamps that are installed on the bumper skirt and the removal of the bumper skirt and end pieces. Once holding the bumper, unscrew the bolts that hold the bumper bracket to the frame and then to the bumper followed by re-screwing back after the order in the reverse order of the actions.
Bumper Cover
FB01-50-221
Q:
How to remove and install the rear bumper and shock absorber on Mazda RX-7?
A:
Open the rear glass hatch and peel back the floor covering at the rear of the luggage compartment. On each side of the floor, there are service holes covered by plates; remove the two securing screws and lift off the covers. Access the lock nut and jam nut of the shock absorber piston inside the service holes. Raise the rear end of the vehicle and support it firmly with stands for the remaining procedures. Under the bottom lip of the bumper, locate the shock absorber mounting brackets and attaching nuts, marking around these brackets on the body panel. Remove the four nuts (two on each side bracket) while supporting the bumper assembly, then lift the bumper assembly away from the car. Inspect the shock absorber and measure the length of the spring, which should be approximately 2.50 in (64 mm); if not, replace the shock absorber with a new one. To install the rear bumper, lift it into position and loosely install the four securing nuts. Adjust the bumper to align with the identification marks made during disassembly, then tighten the four nuts. Tighten the lock nuts and jam nuts inside the vehicle and install the access hole covers, followed by placing the floor covering back in its original position.