How to remove and install the Clutch Slave Cylinder on Mazda 3?

To remove the Clutch Slave Cylinder, first raise the vehicle and support it securely on jackstands, then remove the lower splash shield and the shield under the radiator. At the Clutch Slave Cylinder, pull the hydraulic line locking clip out and remove the line, having a small can and rags ready to catch any spilled fluid; plug the line to prevent excessive loss and contamination. Be aware that a seal ring may fall off or remain on the Clutch Slave Cylinder side. Next, remove the Clutch Slave Cylinder mounting bolts and then the Clutch Slave Cylinder itself. For installation, insert the locking clip into the Clutch Slave Cylinder and connect the hydraulic line fitting. Install and tighten the mounting bolts to the specified torque. Check the fluid level in the brake fluid reservoir, adding brake fluid that meets DOT 3 specifications until the level is correct, and then bleed the system before rechecking the brake fluid level.

How to remove and install the Clutch Slave Cylinder on Mazda 6?

In order to take the Clutch Slave Cylinder off, firstly put the front up and place the vehicle on jackstands. The second step would be to remove the splash shield by unscrewing and un-push-pinning. Unscrew the hydraulic line at the Clutch Slave Cylinder with a flare-nut wrench, be sure to have a small can and rags to receive any spilled fluid; plug the line to avoid too much loss and pollution. Then take off the mounting bolts of the Clutch Slave Cylinder and then take off the cylinder. To install, just use your fingers at first and connect the hydraulic line fitting with the Clutch Slave Cylinder. When attached, apply the mounting bolts up to the recommended torque and attach the hydraulic fitting using a flare-nut wrench. Test the fluorid content of the brake fluid reservoir, pouring in brake fluid which conforms to the specifications of DOT 3 until the right level is reached, and then drain the fluid system after which the level of the brake fluid should be checked again.

Genuine Mazda Clutch Slave Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Clutch Slave Cylinders found

View related parts
Mazda Slave Cylinder Part Number: NE55-41-92XA
$61.11 MSRP: $81.49
You Save: $20.38 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Clutch Release
- Replaces: NE55-41-92X
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, Special Edition, Sport, SV, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Slave Cylinder Part Number: F151-41-92XB
$81.66 MSRP: $108.91
You Save: $27.25 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Cylinder
- Replaces: F151-41-92XA, F151-41-92X, F151-41-920
Fits the following Mazda Models:
- RX-8 | 2004-2011 | 40th Anniversary Edition, Base, Grand Touring, R3, Shinka, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Slave Cylinder Part Number: D651-41-920B
$83.68 MSRP: $111.58
You Save: $27.90 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Clutch Release
Fits the following Mazda Models:
- 2 | 2011-2014 | Sport, Touring | 4 Cyl 1.5 L GAS
View related parts
Mazda Slave Cylinder Part Number: KB7W-41-920
$88.23 MSRP: $117.65
You Save: $29.42 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Clutch Release; Slave Cylinder
- Replaces: BFD1-41-920B, BFD1-41-920A, BFD1-41-920
Fits the following Mazda Models:
- 3 | 2012-2018 | Grand Touring, i, i Grand Touring, I Sport, i SV, I Touring, s Grand Touring, s Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
- 6 | 2014-2018 | Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
- CX-5 | 2013-2016 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View More
View related parts
Mazda Slave Cylinder Part Number: ND6A-41-920
$98.93 MSRP: $131.93
You Save: $33.00 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Clutch Release; Slave Cylinder
- Replaces: N251-41-920
Fits the following Mazda Models:
- MX-5 Miata | 2016-2022 | 100th Anniversary Special Edition, Club, Grand Touring, RF 100th Anniversary Special Edition, RF Club, RF Grand Touring, RF GT, Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Slave Cylinder Part Number: FA42-41-920A
$96.66 MSRP: $128.90
You Save: $32.24 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Cylinder
Fits the following Mazda Models:
- RX-7 | 1984-1985 | GS, GSL, S | 2 Cyl 1.1 L GAS
View related parts
Mazda Slave Cylinder Part Number: BCKN-41-92XA
$99.58 MSRP: $132.79
You Save: $33.21 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Clutch Release; Slave Cylinder
- Replaces: BCKN-41-92X
Fits the following Mazda Models:
- 3 | 2019-2023 | 2.0, 2.5 S, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Carbon Edition, Preferred, Premium, Select | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Slave Cylinder Part Number: BR74-41-920A
$101.73 MSRP: $135.65
You Save: $33.92 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Cylinder
Fits the following Mazda Models:
- Protege | 1994-1995, 1990-1991 | 4WD, Base, DX, ES, LX, SE | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Slave Cylinder Part Number: GP9A-41-920
$112.13 MSRP: $149.52
You Save: $37.39 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Clutch Release
Fits the following Mazda Models:
- 6 | 2006-2007 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Slave Cylinder Part Number: BL3K-41-92X
$125.90 MSRP: $167.89
You Save: $41.99 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Clutch Release
- Replaces: BL3K-41-920
Fits the following Mazda Models:
- Protege | 2001-2003 | DX, ES, LX, Mazdaspeed, MP3 | 4 Cyl 2.0 L GAS
- Protege5 | 2002-2003 | Base | 4 Cyl 2.0 L GAS
View related parts
Mazda Slave Cylinder Part Number: BP4S-41-920D
$137.76 MSRP: $183.72
You Save: $45.96 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Clutch Release
- Replaces: CD85-41-920, BP4S-41-920B, BP4S-41-920A, BP4S-41-920C
Fits the following Mazda Models:
- 3 | 2004-2013 | i, Mazdaspeed, S, SP23 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
- 5 | 2012-2014, 2006-2010 | Grand Touring, Sport, Touring | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Slave Cylinder Part Number: FB01-41-920A
$138.71 MSRP: $184.99
You Save: $46.28 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Cylinder
Fits the following Mazda Models:
- RX-7 | 1986-1991 | Base, Base 2+2, Convertible, GTU, GTUs, GXL, GXL 2+2, LX, LX 2+2, SE, SE 2+2, Sport | 2 Cyl 1.3 L GAS
View related parts
Mazda Slave Cylinder Part Number: FD01-41-920
$150.34 MSRP: $200.49
You Save: $50.15 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Cylinder
Fits the following Mazda Models:
- RX-7 | 1993-1995 | Base, R1, R2, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Slave Cylinder Part Number: B37F-41-920B
$157.76 MSRP: $210.39
You Save: $52.63 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder, Clutch Release
- Replaces: B37F-41-920A, B37F-41-920
Fits the following Mazda Models:
- 3 | 2007-2013 | Mazdaspeed, S | 4 Cyl 2.3 L GAS
View related parts
Mazda Slave Cylinder Part Number: FA01-41-920
Product Specifications
- Other Name: Release Cylinder
Fits the following Mazda Models:
- RX-7 | 1984-1985
View related parts
Mazda Slave Cylinder Part Number: HE29-41-920B
Product Specifications
- Other Name: Release Cylinder
Fits the following Mazda Models:
- MPV | 1989-1991 | Cargo, Passenger | 4 Cyl 2.6 L GAS
View related parts
Mazda Slave Cylinder Part Number: B455-41-920A
Product Specifications
- Other Name: Release Cylinder
- Replaces: B455-41-920
Fits the following Mazda Models:
- 323 | 1990-1994 | Base, SE | 4 Cyl 1.6 L GAS
- MX-3 | 1992-1995 | Base | 4 Cyl 1.6 L GAS
- Protege | 1996-2001, 1994, 1990 | 4WD, Base, DX, ES, LX, SE | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View More
View related parts
Mazda Slave Cylinder Part Number: 1F80-16-540B
Product Specifications
- Other Name: Cylinder, Clutch Slave
Fits the following Mazda Models:
- B2300 | 2001-2009, 1994-1997 | Base, SE, SX | 4 Cyl 2.3 L GAS
- B2500 | 1998-2001 | SE, SX, Troy Lee | 4 Cyl 2.5 L GAS
- B3000 | 1998-2007, 1994-1996 | Base, DS, SE, SX, Troy Lee | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
- B4000 | 1994-2009 | Base, DS, LE, SE, Troy Lee | 6 Cyl 4.0 L GAS
- Navajo | 1991-1994 | DX, LX | 6 Cyl 4.0 L GAS
View More
View related parts
Mazda Slave Cylinder Part Number: 4084-41-920
Product Specifications
- Other Name: Release Cylinder
Fits the following Mazda Models:
- B2000 | 1984 | Sundowner Base, Sundowner SE-5, Sundowner Sport | 4 Cyl 2.0 L GAS
View related parts
Mazda Slave Cylinder Part Number: B181-41-920
Product Specifications
- Other Name: Release Cylinder
Fits the following Mazda Models:
- 323 | 1988-1989 | Base, DX, GT, GTX, LX, SE | 4 Cyl 1.6 L GAS

| Page 1 of 2 |Next >

1-20 of 24 Results

Mazda Clutch Slave Cylinder

Mazda Clutch Slave Cylinder converts simple pedal pressure into the exact movement to release the clutch plates to give every driver crisp shifts and immediate control. Mazda established its reputation on fun handling, innovative rotary power and today, fuel-saving Skyactiv technology that provides punchy performance without wasting gas. The brand combines its engines with responsive steering, elegant Kodo styling and i-Activsense technology such as radar cruise and lane keeping to make journeys safe but exciting. Mazda also plays with electric and mild hybrids and their i-Activ AWD deals with rough roads with confidence, all of which is a show of commitment to constant improvement and making cars that feel alive in the hands of anyone who loves driving. Within that lineup of fun is the small but important hero Clutch Slave Cylinder. Working in conjunction with the master cylinder, the Clutch Slave Cylinder is a hydraulic device that uses hydraulic pressure to push a rod or bearing to release the clutch to allow smooth gear engagement and protect the transmission from grinding. Modern Mazda vehicles use this lightweight hydraulic unit in preference to heavier mechanical linkages, which means there is a predictable pedal feel that even compensates for small wear. Whether mounted externally for easy access or concentrically around the input shaft for weight saving reasons, it is found supporting every manual-equipped Mazda and ensuring that each shift is quick, reliable, and satisfying.

You'll get great performance and real durability when you pick genuine OEM Clutch Slave Cylinder. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Clutch Slave Cylinder Parts and Q&A

Slave Cylinder
BP4S-41-920D
Q: How to remove and install the Clutch Slave Cylinder on Mazda 3?
A:
To remove the Clutch Slave Cylinder, first raise the vehicle and support it securely on jackstands, then remove the lower splash shield and the shield under the radiator. At the Clutch Slave Cylinder, pull the hydraulic line locking clip out and remove the line, having a small can and rags ready to catch any spilled fluid; plug the line to prevent excessive loss and contamination. Be aware that a seal ring may fall off or remain on the Clutch Slave Cylinder side. Next, remove the Clutch Slave Cylinder mounting bolts and then the Clutch Slave Cylinder itself. For installation, insert the locking clip into the Clutch Slave Cylinder and connect the hydraulic line fitting. Install and tighten the mounting bolts to the specified torque. Check the fluid level in the brake fluid reservoir, adding brake fluid that meets DOT 3 specifications until the level is correct, and then bleed the system before rechecking the brake fluid level.
Slave Cylinder
GP9A-41-920
Q: How to remove and install the Clutch Slave Cylinder on Mazda 6?
A:
In order to take the Clutch Slave Cylinder off, firstly put the front up and place the vehicle on jackstands. The second step would be to remove the splash shield by unscrewing and un-push-pinning. Unscrew the hydraulic line at the Clutch Slave Cylinder with a flare-nut wrench, be sure to have a small can and rags to receive any spilled fluid; plug the line to avoid too much loss and pollution. Then take off the mounting bolts of the Clutch Slave Cylinder and then take off the cylinder. To install, just use your fingers at first and connect the hydraulic line fitting with the Clutch Slave Cylinder. When attached, apply the mounting bolts up to the recommended torque and attach the hydraulic fitting using a flare-nut wrench. Test the fluorid content of the brake fluid reservoir, pouring in brake fluid which conforms to the specifications of DOT 3 until the right level is reached, and then drain the fluid system after which the level of the brake fluid should be checked again.