How to remove and reinstall the steering knuckle and wheel hub components on Mazda 3?

To remove the cover of the wheel, loosen the driveaxle/hub nut but not remove it and then loosen the lug nuts of the wheel. Lift the vehicle and place it on jackstands to hold it in place and then take off the wheel and splash shields. The next step is to take off the brake caliper, without disconnecting the brake hose, caliper mounting bracket and caliper disc. Loose the knuckle on the strut body using a hammer, where necessary. To install, position the knuckle and hub assembly strut and at the same time insert the driveaxle into the hub push the strut-to-knuckle pinch bolt to the recommended torque. Attach the balljoint to the knuckle, and screw the pinch bolt/nut to the required torque. Also, screw the tie-rod end to the steering knuckle arm and screw the nut to the requested torque. Install the caliper by fitting the brake disc on the hub. Install the driveaxle/hub nut, screw it in, half-tight. Install lug nuts and wheel and lower the car, ensure the lug nuts are tightened to the required torque. Lastly is to tighten the driveaxle/hub nut to the required torque and put the wheel cover back on, not forgetting to make sure that the front-end alignment has been checked and adjusted accordingly.

How to remove and install the Steering Knuckle on Mazda B2000?

Removal and installation of the components To take out the parts, start by elevating and propping the front end with jackstands, and then take off the wheels. The second step is to remove the brake drums or calipers and then hang the calipers with a wire without unscrewing the brake line. Next take the hub and bearings off, then take the tie rod-to-knuckle nut off, and make use of a ball joint separator to loosen the tie rod end of the knuckle. When using a model up to 1984, loosen the shock absorber, and use a spring compressor on the coil spring to hold the lower arm up by a floor jack. Remember to disconnect the lower ball joint to the knuckle through removing the cotter pin and nut and then using ball joint separator. This should be repeated with the upper ball joint. Once the knuckle and spindle assembly has been taken off the control arms, the knuckle arm can be detached. Wipe down and check all parts that have been worn or damaged and replace them. Install the knuckle arm by securing the knuckle in a vise and tightening the bolts to 70-74 ft. lbs. The knuckle assembly is installed in the opposite sequence of removal with certain torque values of high ball joint-knuckle upper, lower ball joint-knuckle, and tie rod end-knuckle.

Genuine Mazda Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

204 Steering Knuckles found

View related parts
Mazda Knuckle Part Number: NE51-26-12XC
$717.38 MSRP: $980.23
You Save: $262.85 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spindle(Left), Hub; Knuckle
- Position: Left
- Replaces: NE51-26-12XB
Fits the following Mazda Models:
- MX-5 Miata | 2006-2015 | 25th Anniversary Edition, Base, Club, Club Spec, Grand Touring, Special Edition, Sport, SV, Touring | 4 Cyl 2.0 L GAS
View related parts
Mazda Knuckle Part Number: F189-26-11X
$666.27 MSRP: $910.38
You Save: $244.11 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Support(Right), Hub; Knuckle
- Position: Right
Fits the following Mazda Models:
- RX-8 | 2009-2011 | Grand Touring, R3, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Knuckle Part Number: F189-26-12X
$734.00 MSRP: $1002.93
You Save: $268.93 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Support(Left), Hub; Knuckle
- Position: Left
Fits the following Mazda Models:
- RX-8 | 2009-2011 | Grand Touring, R3, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Knuckle Part Number: F151-26-12XA
$850.28 MSRP: $1161.81
You Save: $311.53 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Support(Left), Hub; Knuckle
- Position: Left
- Replaces: F151-26-12X, F152-26-12X
Fits the following Mazda Models:
- RX-8 | 2004-2008 | 40th Anniversary Edition, Base, Grand Touring, Shinka, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Knuckle Part Number: F151-26-11XA
$874.53 MSRP: $1194.95
You Save: $320.42 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Support(Right), Hub; Knuckle
- Position: Right
- Replaces: F152-26-11X, F151-26-11X
Fits the following Mazda Models:
- RX-8 | 2004-2008 | 40th Anniversary Edition, Base, Grand Touring, Shinka, Sport, Touring | 2 Cyl 1.3 L GAS
View related parts
Mazda Knuckle Part Number: G21D-26-122C
$1075.80 MSRP: $1469.96
You Save: $394.16 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spindle(Left), Hub
- Position: Left
Fits the following Mazda Models:
- 6 | 2006-2007 | i, Mazdaspeed, S | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Knuckle Part Number: KD45-28-999
$7.03 MSRP: $9.38
You Save: $2.35 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Washer; Knuckle, Strut Washer
- Replaced by: KSH6-28-999
Fits the following Mazda Models:
- 3 | 2019-2024 | 2.5 Carbon Turbo, 2.5 Turbo, 2.5 Turbo Premium Plus, Base, Preferred, Premium, Select, Select Sport | 4 Cyl 2.5 L GAS
- 6 | 2014-2021 | Carbon Edition, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.5 L GAS
- CX-3 | 2016-2021 | Grand Touring, Sport, Touring | 4 Cyl 2.0 L GAS
- CX-30 | 2020-2023 | 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
- CX-5 | 2013-2024 | 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, 2.5 Turbo Signature, Carbon Edition, Carbon Edition Turbo, Grand Select, Grand Touring, Grand Touring Reserve, Signature, Sport, Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L DIESEL, 4 Cyl 2.5 L GAS
- CX-9 | 2016-2023 | Carbon Edition, Grand Touring, Signature, Sport, Touring, Touring Plus | 4 Cyl 2.5 L GAS
View More
View related parts
Mazda Knuckle Part Number: DGH9-33-03Y
$74.38 MSRP: $99.19
You Save: $24.81 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Left), Steering; Knuckle
- Position: Left
- Replaces: DGH9-33-031
Fits the following Mazda Models:
- CX-30 | 2020-2023 | 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Knuckle Part Number: VA40-33-021B
$85.84 MSRP: $114.47
You Save: $28.63 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Right), Steering; Knuckle
- Position: Right
Fits the following Mazda Models:
- CX-50 | 2023-2024 | 2.5 S, 2.5 Turbo | 4 Cyl 2.5 L GAS
View related parts
Mazda Knuckle Part Number: VA40-33-031B
$85.84 MSRP: $114.47
You Save: $28.63 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Left), Steering; Knuckle
- Position: Left
Fits the following Mazda Models:
- CX-50 | 2023-2024 | 2.5 S, 2.5 Turbo | 4 Cyl 2.5 L GAS
View related parts
Mazda Knuckle Part Number: EF91-33-021
$93.64 MSRP: $124.87
You Save: $31.23 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Right), Steering
- Position: Right
Fits the following Mazda Models:
- Tribute | 2008-2011, 2006 | Hybrid, i, S | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mazda Knuckle Part Number: EC01-33-021D
$107.35 MSRP: $143.16
You Save: $35.81 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Right), Steering
- Position: Right
- Replaces: EC01-33-021C, EC01-33-021A
Fits the following Mazda Models:
- Tribute | 2001-2006 | DX, ES, i, LX, S | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Knuckle Part Number: EC01-33-031D
$107.35 MSRP: $143.16
You Save: $35.81 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Left), Steering
- Position: Left
- Replaces: EC01-33-031A, EC01-33-031C
Fits the following Mazda Models:
- Tribute | 2001-2006 | DX, ES, i, LX, S | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mazda Knuckle Part Number: DGH9-33-02Y
$120.83 MSRP: $161.13
You Save: $40.30 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Right), Steering; Knuckle
- Position: Right
Fits the following Mazda Models:
- CX-30 | 2020-2023 | 2.5 S, 2.5 S Carbon Edition, 2.5 Turbo, Base, Preferred, Premium, Select | 4 Cyl 2.5 L GAS
View related parts
Mazda Knuckle Part Number: B25D-33-031B
$21.45 MSRP: $166.90
You Save: $145.45 (88%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Left), Steering
- Position: Left
Fits the following Mazda Models:
- Protege | 1999-2000 | DX, ES, LX | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View related parts
Mazda Knuckle Part Number: C461-33-021A
$131.73 MSRP: $175.67
You Save: $43.94 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Right), Steering
- Position: Right
- Replaced by: C461-33-021B
Fits the following Mazda Models:
- 5 | 2012, 2006-2010 | Grand Touring, Sport, Touring | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Mazda Knuckle Part Number: C461-33-021B
$131.73 MSRP: $175.67
You Save: $43.94 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Right), Steering
- Position: Right
- Replaces: C236-33-021, C273-33-021A, C461-33-021A, C461-33-021, C273-33-021, C273-33-021B
Fits the following Mazda Models:
- 5 | 2012-2015 | Grand Touring, Sport, Touring | 4 Cyl 2.5 L GAS
View related parts
Mazda Knuckle Part Number: DN4E-33-021
$122.71 MSRP: $163.65
You Save: $40.94 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Right), Steering; Knuckle
- Position: Right
Fits the following Mazda Models:
- MX-30 EV | 2022-2023 | Base, Premium Plus | BATTERY EV (EV/BEV)
View related parts
Mazda Knuckle Part Number: DN4E-33-031
$122.71 MSRP: $163.65
You Save: $40.94 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Left), Steering; Knuckle
- Position: Left
Fits the following Mazda Models:
- MX-30 EV | 2022-2023 | Base, Premium Plus | BATTERY EV (EV/BEV)
View related parts
Mazda Knuckle Part Number: C100-33-021B
$124.54 MSRP: $166.08
You Save: $41.54 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle(Right), Steering
- Position: Right
- Replaces: C100-33-021A
Fits the following Mazda Models:
- Protege | 2000-2003 | DX, ES, LX, Mazdaspeed, MP3 | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Protege5 | 2002-2003 | Base | 4 Cyl 2.0 L GAS

| Page 1 of 11 |Next >

1-20 of 204 Results

Mazda Steering Knuckle

The Mazda Steering Knuckle provides fine wheel control which keeps every ride balanced and responsive. Mazda rose to fame through daring rotary engines in the 1960s and the company built its reputation with Skyactiv technology that wrings more fun from every drop of fuel. The company combines Kodo design with i-Activsense aids; cars take on a life of their own and drivers become aware on busy streets. Mazda also plays with electric drive and mild hybrids while its i-Activ AWD handles slippery or rough surfaces without any drama. Drivers often rave about the brand for a light, connected steering feel that turns daily errands into moments of enjoyment, proving that Mazda values emotion just as much as efficiency. Shifting focus to the heart of that feel, the Steering Knuckle is located at the pivot point between suspension and wheel, forged from strong steel or aluminum to remain light and rigid. This part connects the hub, bearings, ball joints, and tie rod, allowing the wheel to turn smoothly but hold alignment over bumps and during hard braking. A well-developed Mazda Steering Knuckle has a common hub-type layout throughout the lineup, which means front-drive or all-wheel versions are durable without extra weight. By resisting flex and spreading road loads, the component protects tire wear, maintains true steering angles, and preserves the spirited handling that defines Mazda.

You'll get great performance and real durability when you pick genuine OEM Steering Knuckle. Mazda builds these using high-quality materials and official factory methods to ensure they hold up mile after mile. You deserve that Mazda reliability without the headache of cheap knockoffs. It is easy to find exactly what you need in our huge inventory of genuine parts. Plus, every OEM part carries a real manufacturer's warranty for your peace of mind. You will love our low prices too. Order today and we will ship your brand-new parts fast. They often reach your door in just a few days.

Mazda Steering Knuckle Parts and Q&A

Knuckle
BP4L-33-021
Q: How to remove and reinstall the steering knuckle and wheel hub components on Mazda 3?
A:
To remove the cover of the wheel, loosen the driveaxle/hub nut but not remove it and then loosen the lug nuts of the wheel. Lift the vehicle and place it on jackstands to hold it in place and then take off the wheel and splash shields. The next step is to take off the brake caliper, without disconnecting the brake hose, caliper mounting bracket and caliper disc. Loose the knuckle on the strut body using a hammer, where necessary. To install, position the knuckle and hub assembly strut and at the same time insert the driveaxle into the hub push the strut-to-knuckle pinch bolt to the recommended torque. Attach the balljoint to the knuckle, and screw the pinch bolt/nut to the required torque. Also, screw the tie-rod end to the steering knuckle arm and screw the nut to the requested torque. Install the caliper by fitting the brake disc on the hub. Install the driveaxle/hub nut, screw it in, half-tight. Install lug nuts and wheel and lower the car, ensure the lug nuts are tightened to the required torque. Lastly is to tighten the driveaxle/hub nut to the required torque and put the wheel cover back on, not forgetting to make sure that the front-end alignment has been checked and adjusted accordingly.
Knuckle
UB39-33-031B
Q: How to remove and install the Steering Knuckle on Mazda B2000?
A:
Removal and installation of the components To take out the parts, start by elevating and propping the front end with jackstands, and then take off the wheels. The second step is to remove the brake drums or calipers and then hang the calipers with a wire without unscrewing the brake line. Next take the hub and bearings off, then take the tie rod-to-knuckle nut off, and make use of a ball joint separator to loosen the tie rod end of the knuckle. When using a model up to 1984, loosen the shock absorber, and use a spring compressor on the coil spring to hold the lower arm up by a floor jack. Remember to disconnect the lower ball joint to the knuckle through removing the cotter pin and nut and then using ball joint separator. This should be repeated with the upper ball joint. Once the knuckle and spindle assembly has been taken off the control arms, the knuckle arm can be detached. Wipe down and check all parts that have been worn or damaged and replace them. Install the knuckle arm by securing the knuckle in a vise and tightening the bolts to 70-74 ft. lbs. The knuckle assembly is installed in the opposite sequence of removal with certain torque values of high ball joint-knuckle upper, lower ball joint-knuckle, and tie rod end-knuckle.